OF THE DRAW THE SHEAR AND WOHENT DIAGRAM , AND THE ELASTIC CURVE SHOWN SHOW COMPLETE SOWTIONS AND NECESSABY FIGURES. LOADED FRAME

Q: Given in the accompanying sketch is a cross-section which has been plotted from soundings taken…

A:

Q: LINE LATITUDE (m) DEPARTURE (m) АВ 100 50 ВС 200 200 CA -300 -250

A: Calculating the DMD(Double meridian distance): Double meridian distance of any line=DMD of preceding…

Q: ing Problem ean sheet . Draw the shear and bending moment Diagram of the following A) 71kN/m A B 8 m…

A:

Q: Considering the topographic map below, a) What is the contour interval? b) What is the lowest…

A:

Q: 2.3 Considering the flow upstream of a sluice gate, the gate closes suddenly. The initial flow…

A: 2.3 Considering the flow upstream of a sluice gate, the gate closes suddenly. The initial flow…

Q: For an actual ship that is required to sail at a speed of 12 m/s, a 1:50 scale model is prepared and…

A:

Q: ncentration of 100 mg/L using a settling column was carried out in a oratory. The results of the…

A: Given - L = 45 M B= 12 m Q =8.1 MLD  =8.1×106 LD     Q =8.1×103  m3/sec24×60×60      Q=0.09375…

Q: Draw the shear and moment diagrams of the beams shown using the area method. 30 kN 9 kN/m A B 3m 2m

A:

Q: Draw the node network, perform the CPM calculations (ES, EF, LS, LF, TF, and FF), mark the critical…

A:

Q: 2. A suspension of particles with a particle density of 2796 kg/m³ is settling in water with a…

A: Given Specific gravity G = 2796/1000 = 2.796  Kinematic viscosity of water at 20 ° C = 1.004 × 10 -6…

Q: Last two digit 30

A: yn=1m R=yn=1m ( for wide rectangular channel)

Q: Determine support reactions in the frame on the left and generate bending moment, shear force, and…

A:

Q: A 10-foot high by 75-foot long wall will be faced with standard size brick 3 1/2 x 2 1/4 x 8…

A: Wall is a structural member which has many uses such as It act as a partition for rooms It act as a…

Q: A 0.75 in. diameter rod is subjected to 800 lbf and 200 lbf shown in the figure. Determine the state…

A: A torsion-force is a load subjected to a material by twisting it. A shear stress is generated by the…

Q: mal stress for the steel used i e beam to support the loadim

A:

Q: State of stress at a point in a material is as shown in the Figure 3 100 N/mm? 75 N/mm - 50 Nmm2…

A:

Q: Cost and Estimation:

A: The objective of the question is to calculate the total cost of purchasing, loading, transporting,…

Q: What is the length of the dividing line? (Type your answer using 2 decimal places, numerical value…

A:

Q: For the load diagram shown below, identify the corresponding shear and bending moment diagrams.

A:

Q: A beam has a cross-section as shown. At a section where the shear force is 12 kN, 100 mm a.…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: 80 11 B 10 mm 10 mm 80 10 mm

A:

Q: 13,12 S 2 m 2 26 26AN 4m h H 5,3 ។ ५

A:

Q: The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD…

A: TAB=800N-mTBC=2400N-mTCD=2400N-m

Q: .) Determine shear and moment equations of the beam shown. Neglect horizontal reactions since ther…

A:

Q: Soil Compaction 1. A series of Modified Proctor Tests have been perfomed on a soil that has a unit…

A:

Q: 300 mm PDL = 15 kN/m , PLL = 5 kN/m 2 - 16mm 4m 5m 3m 450 mm fel - 20 Z MPa 4 - 25mm

A: Note:- As per guidelines we are allowed to solve first three supports in case of multiple sub-parts…

Q: 1. A miniature model of the famous Taipei 101 will be made by pouring plaster of Paris in a cast.…

A: Taipei: It is a skyscraper in Taiwan's Taipei area. Until the completion of the Burj Khalifa, it had…

Q: AA County Foad c6o wie) For the rectangular shown, the county road is to be place such that the…

A: Given: The diagram is a rectangle.

Q: Design Column B2 shown on the floor plan, as a square tied reinforced concrete column. The column is…

A:

Q: 14.17 Calculate the value of S and Z and the shape factor for the beam cross sections shown.

A: Given: A tee section and a hollow rectangular section  Required: Elastic section modulus, plastic…

Q: 4. For the system shown in the figure below: Datum 5.0 m 7.0 m 5.0 m a) Flow rate per meter length…

A: Given data in question  Flownet Head difference  Void ratio Specific gravity  To find out  Discharge…

Q: Two rods are connected to each other and are restrained at top and bottom. The top portion is steel…

A:

Q: The CSTR shown in Figure is used to treat an industrial waste, using a reaction which destroys the…

A:

Q: A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine…

A: The values and diagram given in the question are as follows: Specific gravity of alcohol(Sg)=0.78

Q: Given the figure below, Solve for the following unknowns. [ 16 m A RA, RA, = MA Determine the…

A:

Q: 2. Determine whether each of the trusses below are internally determinate, indeterminate, or…

A:

Q: The part of the shown graph shows no permanent deformation. Select one: a. Black b. Red C. Green d.…

A: The given graph is stress-strain curve of mild steel.

Q: Problem I. The masses of the frictionless cylinders A and B are 2.0 kg and 1.0 kg, respectively.…

A:

Alloys

An alloy is an admixture of two or more metals or a metal and a non-metal. Since ancient times, man has been using alloys. Alloying helps to retain the properties of the parent matter, such as hardness, strength, toughness, ductility and is corrosion-resistant. Copper alloys such as brass have antimicrobial properties that help to fight against (Coronavirus disease 2019) COVID-19 and other hospital-acquired infections. Some common alloys are brass, bronze, solder steel, etc. Most alloys have a lower melting point than their constituents. This is due to the presence of a nonmetal as one of the constituents that behaves as an impurity and restricts the raise of melting point.