Given the figure below, Solve for the following unknowns. [ 16 m A RA, RA, = MA Determine the Reactions and Moments in kN and kN.m. respectively. W RB, 10 m RB, B 23 kN/m 143 kN

Q: On a map of scale 1:75,000 the map distance measured between points A and B is 5.0 cm. If a sketch…

A: Find scale for sketch of same area

Q: Problem Solving: 1. From the given frame shown it is supported by a hinged at A and a roller at C.…

A: To find deflection,  unit load method has been used.

Q: Calculate the end areas for depths of fill from 0 to 20 ft using increments of 2 ft for level…

A:

Q: Explain the three components of Engineering Şurveying.

A: Solution: Engineering surveying are basically those activities which are involved in the planning…

Q: Subject:Geographic Information System Show how spatial data (Such as Raster Data) analytics are…

A: A system called a geographic information system (GIS) is one that collects, organises, processes,…

Q: Write Penman equation flowchart to calculate ET= K.ET, - Κ.ΕΤ

A: Penman equation flowchart to calculate ET=K.ETp as follows

Q: Compare the bar chart with the network diagram system/.

A: Bar Chart: The Bar chart is also known as the Gantt chart, which is a common project management tool…

Q: Describe implicit time method.

A: Describe implicit time method.

Q: QUESTION 1: ISOMETRIC Q1(a): Taking X as the lowest view point, sketch the isometric view of the…

A: Given details are- Top view , front view and side view The hand drawing of isometric view is…

Q: 1. What is Airspace Charting? 2. How do you read an Airspace Chart? 3. What charts do pilots use? 4.…

A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…

Q: Please make your own question about horizontal distance (surverying) and solve it on your own. Make…

A:

Q: What are the errors faced in electronic distance measurement?

A: Electronic distance measurement  is a device which measure the distance  with help of infrared,…

Q: 7. PROFILE file of pro- level notes and show the customary arithmetic check. LEVELING. Complete the…

A: Given: The differential leveling notes are given below, STA BS HI FS IFS ELEV BM-0…

Q: an object moving horizontally after t seconds is given by the it3 +36t2-54t, where s is measured in…

A:

Q: Solve ONLY LETTER D and E.  The first three subparts are already answered in my previous question.…

A:

Q: Civil Engineering What is rubber sheeting or conflation as used in GIS? What problems must be…

A:

Q: 80 11 B 10 mm 10 mm 80 10 mm

A:

Q: d. e. f. Using a ruler to measure a box in front of you is an example of an indirect observation.…

A: Answers (d) Using a ruler to measure a box in front of you is an example of an indirect observation…

Q: Draw the shear and moment diagram of the given beam using any method. 50 kN 15 kN/m 150 kN-m B C -6…

A:

Q: Lil Sample Problem 2 2. Calculate the velocity of water flowing in point 2? Water Open Tank

A: The depth of water in tank, h=3mThe tank is opoen to atmosphere.

Q: centroid C of the beam having the cross-sectional area shown 150 mm 150 mm 20 mm 20 mm B

A:

Q: Complete the missing data. LINE DISTANCE (meter) BEARING 1-2 2-3 123.4450 S 73.45° E 3-4 140.2336 N…

A:

Q: Given the following data, find the required area.. Corner 1 2 300 400 X coordinate, m 300 800 Y…

A:

Q: What are the Deviation Requests?

A: Deviation requests : A deviation request is a document that is generated by a supplier (or more…

Q: earson MyLab and Mastering X roblem 9.19…

A:

Q: Explain how data can be converted from raster to vector format. Match the words in the left column…

A: GIS stands for Geographic Information System. It is a computer-based system used to collect, store,…

Q: How do sonar or ultrasonic level measurement works?

A: Sonar is a technique for detecting and estimating the distance and direction of underwater objects…

Q: PLEASE PROVIDE CLEAR

A:

Q: Please calculate elevations in the stations given in the table and show the arithmetic check. Write…

A: Given: The leveling notes are given below, Station BS (m) FS (m) H.I. (m) Elevation (m)…

Q: 5. From the cantilever beam below, determine the value of point load P acting at midspan that will…

A: To find value of load P such that deflection at free end is zero

Q: Process of GIS Mapping O a Data Manipulation. Data Collection, Mapping, Database O b. Data…

A: Data collection,data base,data manipulation,mapping

Q: 1. Tables below show data of stream flow and rainfall observed for a particular watershed with an…

A: (3) The question is based on the streamflow and rainfall data for the particular watershed. The area…

Q: Determine the y. Measure it from the x-axis. 90 mm 70 mm 60 mm 60 mm 40 mm 120 mm

A: y  from x-axisy =40+2h3y =40+2×603y =40+40y =80 mm

Q: a. b. C. d. ÏÏ The most important If a mistake is found Regarding surveying having too much…

A: There are three main sources of error arise: 1) Natural error - climate, wind, humidity etc. 2)…

Q: Laboratory Report 6 – Area Computation (Trapezoidal Rule) Objective: To compute the area using…

A: given, We have Set of Ordinates taken on a ground. Our aim is to calculate area of that land using…

Q: ation tion Military, mining, land development, resource management, hydrography; all these domains…

A: This question is related to the Surveying Engineering from Civil Engineering. In this question ask…

Q: Sadly I cant see the image

A: Given data, Intersection of 2 tangents station is 2+550.  Compound Curve: I 1 =31° ,I 2= 36° ,D1 =…

Q: A series of closely-spaced ridges and valleys occurring at regular intervals.Blank 1 Blank 1 Add…

A: This question is related to Contours from Surveying Engineering.

Frames

The trusses and frames are the two most important structural members of civil engineering. Trusses are the interconnection of links and other structural members. The interconnection with other members makes the system behave as a single member that supports and transfers loads. Trusses are generally two types, plane truss, and space truss. Frames on the other hand form the skeleton of any building construction. Frames are structures formed by the connection of beams, columns, slabs, and joists. These members provide the building with the required structural support.