This is about ommitted measurements which involves 2 non-adjoining sides.... DISTANCE (m)?150.932?E209.613EF134.912FA110.147Sketch the data above and solve for the following.b.a. Length of the Closing LineBearing of the Closing Linec. Distance between A and Bd. Distance between C and DOCCABCDOBSBCDBEARINGN73°17'E$54°43'ES8°43'WS76°34'WN43°10'WN19°25'E

first convert the bearing in WCB

OCC A B C D DISTANCE (m) ? 150.932 ? 209.613 E F 134.912 F A 110.147 Sketch the data above and solve for the following. a. Length of the Closing Line b. Bearing of the Closing Line c. Distance between A and B d. Distance between C and D OBS B C D E BEARING N73°17'E $54°43'E S8°43'W S76°34'W N43°10'W N19°25'E

OCC A B C D DISTANCE (m) ? 150.932 ? 209.613 E F 134.912 F A 110.147 Sketch the data above and solve for the following. a. Length of the Closing Line b. Bearing of the Closing Line c. Distance between A and B d. Distance between C and D OBS B C D E BEARING N73°17'E $54°43'E S8°43'W S76°34'W N43°10'W N19°25'E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please solve for h and explain...thanks!
find the values of x 2х, + 3x2 + 2xз %3 4x, — 5х, + 5х; — —7 —3x, + 7x, — 2хз — 5
02-calculate the vertical movement of Points A 5 kulm A mona 1.5 - 2m 3m 4 + 4 + 2 + D=15mm 20kN D = 25mm 50 kN D=35mm E=20x10 N 123 3 2 80
Question 2 • Determine the &. Measure it from the y-axis. 7 in 43 in. 4 in. 8 in. 4 in. « Previous
A student was ask to make a 345.43 m long line using a 25 m long tape taht is 0.0021 m long. What is the required measurement?
A steel tape is 100.00 ft long and has a weight of 0.0225 lb/ft and is used to measure a line from A to B in two segments (one full tape length and one partial tape length), supported at the ends only for each of the two segments. The recorded distance is 181.83 ft. The pull at the time of measurement is 12 lb. What is the length of the line corrected for sag? (Assume that no other tape corrections need to be applied.)
Given: b = 300mm, d = 450mm, As’ = 2D25mm, d’ = 65mm, fc’ = 28MPa, and fy = 415MPa. Solve for ɸMn if: As = 6D32mm
2. During the measurement at the sides of the slope, the data was recorded into three bays, the following information (Table 1.0) was obtained: Table 1.0 Difference in Tension (N) Temperature (°C) Bay Measured Length (m) level between end (m) 1 25.842 19 +0.285 150 27.365 18 -0.236 120 3 21.645 21 -0.239 160 The 30 meter tape used has a mass of 0.400 N/m and a cross-sectional area of 3.00 mm?. It was standardised on the flat at 20 °C under a pull of 100 N, the actual length was 29.995 m during the measuring works. The coefficient of linear expension for the materials of the tape us 0.000015 / °C and Young's Modulus is 20.5 x 104 MN/m?. Calculate the absolute length of survey line in 3 decimal point. Slope correction = -v² 2s Sagging correction = - w²L³ 24P? Tension correction = (P – Ps) EL AE Temperature correction = a (T-Ts) (L)
Five separate measurements were made of a line and their degrees of precision computed as follows: 1st trial, 1/5000; 2nd trial, 1/2500; 3rd trial, 1/6500; 4th trial, 1/7000; 5th trial 1/10000. The measurement which is of a higher degree of precision was the done in which trial?
Problem ABC. Five measurements were made to determine the lenght of a line and recorded as follows: 350.33, 350.22, 350.30, 350.27, and 350.30 meters. The most probable value of the lenght measured was. answer: 350.28 now, On Problem ABC. What will be the residual of the second measurement choices: a. -0.06, b. 0.06, c. -0.02, d. 0.02 -On Problem ABC. What will be the value of probable error of the mean choices: a. 0.08, b. 0.094, c. .085, d. 0.095
A distance of 15.94 m is measured with a tape. During measurement, theother end was discovered to be 0.78 m lower. Find the correct distance.
please please give accurate answer. A line is recorded as 472.90 m long. It is measured with a 0.65 kg tape which is 30.005m long at 20°C under a 50 N pull supported at both ends. During measurement the temperature is 5°C and the tape is suspended under a 75 N pull. The line is measured of 3% grade. What is the true horizontal distance? E = 200 GPa, cross-sectional are of tape is 3 mm² and coefficient of linear expansion is 0.0000116 m/°C.