Obtain the z parameters for the network shown. Take R = 30.

Q: A Proportional-Derivative (PD) controller helps to reduce the overshoot in the response.

A: True.

Q: This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx…

A:

Q: Question 2 : al khat are the differences between logical and Continuous Sensors. b) Name two logical…

A: a) The main differences between logical and continuous sensors lie in the type of data they provide…

Q: How to analyze the circuit ? *Need excitation equation * Need transition equation *State transition…

A: The given circuit is As the output doesn't depend on the input, the FSM is a Moore machine.

Q: A Proportional-Derivative (PD) controller may reduce the stability of the system. Select one: O True…

A:

Q: Could you show how to do the second part as well?

A:

Q: Q) The micro controller is convert the physical quantity to output signal. * T O F

A: The explanation is as follows.

Q: In time the use of the important parameter of the equivalent circuit was determined by the actual…

A:

Q: The purpose of a Yoke in a dc machine is to - a. collect the current  b. provide protection c.…

A: Yoke in DC machine- It is the outer frame of the DC machine which is made up of steel or cast iron.

Q: a) List all the mistakes in Verilog HDL code given for the circuit in Figure 1. b) Suggest the…

A: Given the circuit : ' Given the Verilog code: module Test1(D,clock,Q1,Q2); input(D,clock); output(Q1…

Q: In modeling of P controller, you need for block in Matlab. gain O sine wave оооо constant O step O

A: Types of Controller P controller I controller  D Controller  PI Controller  PD Controller  PID…

Q: Q2: Consider the following control system K, (1+ 18) For K. = 2, tD = 1 and step change in load…

A:

Q: R 12 V 2Ω (a)

A:

Q: Explain diagram

A: Given :   In the above question they have mentioned the 6 bit parallel out shift register circuit.…

Q: Q4) Consider three-stage space-division switch using CLOS criteria with N=450. 2. Calculate the…

A: The ingress stage, the middle stage, and the egress stage are the three stages of CLOS network. Each…

Q: There is a load formed by the series connection of the resistor R0 and the inductance L0 between the…

A:

Q: Find the value of Ip. Voi and Voz in the circuit shown in Figure below.

A: The circuit is as shown below :

Q: V1 12 Vs SINE (1 0.05 5000k 0) Vin Cbp HH 0.1µ U1 LM358 -Vo

A:

Q: What is meant by Paging? Give its advantages

A: Paging: Paging is nothing but a memory management technique that can reduce the need for physical…

Q: Q) The micro controller is convert the physical quantity to output signal. * F O O

A: The explanation is as follows.

Q: i will like

A: Part iiAssuming the system is little-endian, here are the values of r1 and r0 after the instructions…

Q: Differentiate among following: [at least 4 differences] 1. Functional and Non-Functional…

A: 1) Functional testing- Functional testing is a sort of software testing that involves comparing the…

Q: Q4. A// The currents flowing in the lines toward a balanced load connected in A are : I, = 10020°,…

A:

Q: Problem 2: Digital VLSI What is setup time and what is hold time?

A:

Q: AIWhat is the difference between clippers and clampers ? sketch the * .circuit

A:

Q: Write the uses of PI Controller

A: The block diagram of PI controller is given as: The actuating signal is given as: P(s)=K1+K2sR(s)…

Q: outnt InPut deud bund

A:

Q: Explain briefly construction of D.C. machine and What are the functions of a Yoke in DC mạchines?…

A: Construction The DC machine consists of parts like, yoke, poles, armature, armature winding, pole…

Q: Provide state table for following state diagram, and design the mealy machine circuit diagram.

A: First, assign the states using binary encoding. It has 6 states, so required 3 D-flip flops.

Q: 5) Consider the fragment of legv8 assembly below and suppose the pipeline is modified, so that it…

A: Consider the fragment of legv8 assembly below and suppose the pipeline is modified , so that it has…

Q: An 8085 assembly language program is given below. Line 1: MVI A, B5H 2: MVI B, OEH 3: XRI 69H 4: ADD…

A: Given Assembly language program. We have to find the content of accumulator after the execution of…

Q: X- There are three standardized systems of units. They are, ---- a) RPM b) FPS e) Accuracy d) CGS e)…

A: Choose the correct option What is the standard system of units?     as per our guidelines we are…

Q: What is serial in and parallel out

A: Serial in and parallel out is a type of shift register. In this type of register, the input data is…

Q: Alamouti scheme is an example of  A. Space time coding B. MIMO C. None of these

A:

Q: B Y 2. D E F

A:

Q: A system bus can be used to carry the control signals Select one: O True O False

A: The above question is related to  subject of microprocessor There are 3 systems bus that can be…

Q: actuators Question 3: a) Name two logical and two continuous actuators b) Name four techniques used…

A: a) Two logical actuators:1. Solenoid valve: A solenoid valve is an electromechanical device that…

Q: A certain gate has a Speed Power Product of 40 pico Joules and Icc 0.5mA and I CL =2.2mA with a dc…

A: According to the question we have to find the value of the power dissipation and propagation delay.

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.