O Analyze the following horizontal lifeline system: - T = 5,000-Ib, L = 30-ft, x = 4-ft and z = - Calculate V1, V2, H1, H2, T1, T2, a, c1, c2, S1 and S2. - Determine e if Preload tension is 200-Ilb, cable weight 0.5-lb/ft. - Provide the length z-e=? 2-ft (max limit). %3! %3D %3D e T1 V1 V2 T2 s1 H2 H1 S2 L-x 3/6/2013 Temporary Structures 38

O Analyze the following horizontal lifeline system: - T = 5,000-Ib, L = 30-ft, x = 4-ft and z = - Calculate V1, V2, H1, H2, T1, T2, a, c1, c2, S1 and S2. - Determine e if Preload tension is 200-Ilb, cable weight 0.5-lb/ft. - Provide the length z-e=? 2-ft (max limit). %3! %3D %3D e T1 V1 V2 T2 s1 H2 H1 S2 L-x 3/6/2013 Temporary Structures 38

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hanging cable supports a load of 27,000 lbs. Assuming that the weight of the cable is negligible, what is the force in the compression member that holds the ends of the cable apart? What is the force in each segment of the cable?
Chapter Three FUNDAMENTAL PROBLEMS All problem solutions must include an FBD. FE pl F3-1. The crate has a weight of 550 lb. Determine the force in each supporting cable. F3-1 -2. The beam has a weight of 700 lb. Determine the hortest cable ABC that can be used to lift it if the naximum force the cable can sustain is 1500 lb.
h1 = 100 mm h2 = 500 mm B = 350 mm Tension steel, As = 6 of 28 mm diameter bars Compression steel, As’ = 4- 28 mm diameter bars Lateral ties = 12 mm diameter Clear concrete cover = 40 mm Concrete, f’c = 27 MPa Steel, fy (main bars) = 415 Mpa Steel, fyt (ties) = 275 Mpa 1. Determine the minimum spacing “a”, (mm)? (Use kN, use NSCP 2010 provision, the answer must be two (2) decimal places, and avoid rounding off when it's not a final answer) 2. Determine the nominal shear strength (kN) provided by the concrete? (Use kN, use NSCP 2010 provision, the answer must be two (2) decimal places, and avoid rounding off when it's not a final answer) 3. Determine the nominal shear strength if the lateral ties area is spaced at 125 mm on center? (Use kN, use NSCP 2010 provision, the answer must be two (2) decimal places, and avoid rounding off when it's not a final answer)
4. Find the tension in the cable AB A vinovs 916 2931 ows ert b 9ft adl 00001 gnol 1991 81 21 msed srT 819llon bris A niq is anoitosen eri bni S (2jq OS) trigisw mesd sdt siongl bosqz 12 ft B 8ft Sinio adl 0008 4000 lbs
Please include FBD in your solution
The plate ACDE Axed as vertical as shown in Fig H,G, EIA Ball and Socket ) The mo ment 9o KN-m about the line DL n x2 -plane, E H coincided overthe x-axis, Determine the tensIon in Cable ad all reactions in ball and Socket A 2m rcable 2m 4m parrallel fo 2 -20 kN IC neglected MGram 5m G: 6 m frictionless 30 Fig.Q#1
Problem Exercise From the following figure, find the number of 10 mm lateral ties and tie wire if there are 36 columns with cross sectional di- mensions of 60 x 90 cm. at 12.00 meters long per column. 10 - 25 mm main reinforcement- 90 m Lateral Tles .60 m. CROSS SECTION .60 m.
Read the question carefully and give me right solution with clear hand writing.
TABIGNE, KIMBERLY M. 4.) FOR THE CACE OF KNO TTED LORDS SHOWN BELOW, FIND THE TENN IN THE ROPES IF THE SUPPORTED OBJECT WEIGHS G0ON. 170 B 36 A 11 G0ON
show clean solution and fbd pls
Show the complete solution.
Draw the-shear-and-moment-throughout-the-beam-as-functions-of-x