O 4p R=2p 2p 4p X Determinar 1. Localice el Centro de Gravedad de la figura con respecto a los ejes X y Y 2. Calcular el Momento de Inercia con Respecto al eje X 3. Calcular el Momento de Inercia con respecto a un eje x que pasa por el centro de gravedad de la figura compuesta.

Q: The beam cross section shown below has been proposed for a short pedestrian bridge. The cross…

A:

Q: Part B Perform double integration of the bending moment equations. You will obtain deflections in…

A: A simple support beam with the hinge at A, roller support at B, and an overhang portion BC. On span…

Q: Question # 3: The built-up beam is formed by welding together the thin plates of thickness 3 mm. the…

A: Shear center is a point on the beam section where the application of loads does not cause its…

Q: A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The…

A:

Q: The following truss system is Pin Supported at Joint C and Roller Supported at Joint E. Joint B is…

A: A structure is a structure or a frame that is connected in a triangular shape and all members act as…

Q: Problem 2 Consider the beam of length L and cross-sectional moment of inertia I shown in the figure…

A: Given data:

Q: ows an elastic be igidity EI and deflection v(x) d by an equation

A:

Q: 2) Three members of a truss frame into a steel gusset plate as show in Figure 3. All forces are…

A: Given members Rx and Ry be components of resultant forces in x and y direction

Q: All the tension/compression members of the frame structure shown in the figure are pin-jointed and…

A:

Q: The resultant of the three forces as shown in figure is vertical. determine the angle 0, and…

A: All data present in the figure Need to find 1- Resultant force (R)2-  angle ()

Q: A triangular distributed load of max intensity w = 320 N/m acts on beam AB. The beam is supported by…

A:

Q: A beam having the cross section shown is subjected to a couple that acts in a horizontal plane.…

A: z = 1.43 in ( from left side )z = 5 - 1.43  =  3.57 in ( from right side )Iy = 11.3 in4Maximum…

Q: - Determine the reactions at supports A and B.

A:

Q: 4. The truss shown in figure Q4.1 is constructed out of square steel bars, all of which are of 25mm…

A: Given values: Area of members, A = 25 mm * 25 mm = 625 mm2 Young's modulus, E = 200 * 103 MPa Using…

Q: 6...

A: If you have further doubts about this. I will be happy to help you solving this. Thank you!

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.