Consider a rod subjected to stresses such that anelement located on its edge oriented orthogonallyto the horizontal (x) and vertical (y) will havenormal stresses of 0 and 10 MPa (T), respectivelyalong the horizontal and vertical and a shearstress of +6 MPa.1. Draw the state of stress of the elementdescribed above.Using ONLY the stress transformationequations,2. Determine the stresses on the elementoriented at an angle of 0=35°clockwiserelative to the original orientation and sketchthe corresponding element.3. Determine the maximum normal and shearstresses and show these on properly orientedsketches.

Given:A rod element is oriented orthogonally to the horizontal and verticalσx=0 MPaσy=10 MPaτxy= 6…

Answered: normal stresses of 0 and 10 MPa (T)

Engineering

Civil Engineering

normal stresses of 0 and 10 MPa (T)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of 200 mm, a wall thickness of 5 mm, and a length of 5.4 m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 6= i AD= i mm mm
400mm Find the required spacing of intermediate stiffeners if V*=1600KN 25mm • Check the adequacy of a pair of stiffeners 90mmx12mm • Check the web crushing capacity if the reaction of 1600kN is applied over a stiff bearing length of 250mm at the end of the beam (note that the spread of stress can only go in one direction) • Homework extension: Check the adequacy of an endplate stiffener 300 wide by 16mm thick 12mm Use Grade 300 Steel 1440mm
Normal stress is calculated dividing the reaction by the cross-sectional area. Is this approach valid for any point of a structural member? Why or why not? To answer this question, consider the loading point, cross- sectional shape, etc.
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer
11. Iwo beams, one having square cross section and another circular cross-section, are subjected to the same amount of bending moment. If the cross-sectional area as well as the material of both the beams are same then (A) Maximum bending stress developed in both the beams is the same (B) The circular beam experiences more bending stress than the square one (C) The square beam experiences more bending stress than the circular one (D) As the material is same both the beams will experience same deformation
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 15 mm, and a length of 5.5 m. The pipe supports a compressive load of 635 kN. After the temperature of the pipe drops 45°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
2.58 Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the alu- minum bar will be equal to -11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. - 14 in. - Bronze A = 2.4 in² E = 15 x 106 psi a = 12 x 10-6/°F Fig. P2.58 and P2.59 18 in.. Aluminum A = 2.8 in² E = 10.6 x 106 psi a = 12.9 x 10-6/°F 300 mm 0.5 mm 250
Normal stress is calculated dividing the reaction by the cross-sectional area. Is this approach valid for any point of a structural member? Why or why not? To answer this question, consider the loading point, cross- sectional shape, etc.
The steel bars are firmly attached to rigid supports. Initially the temperature is 840F. Determine the stress in bars AC and CB when the temperature becomes -600F. Use E = 29 x 106 psi and α = 6.50 x 10-6/ 0F.
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of 225 mm, a wall thickness of 15 mm, and a length of 5.0m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 48°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = mm AD= i mm
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 225 mm, a wall thickness of 15 mm, and a length of 5.0 m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 48°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe.