Normal blood pressure for a human is 120/80 mm Hg. By modeling a sphygmomanometer pressure gage as a U-tube manometer (as shown in the figure below), convert the systolic pressures (120 mm Hg) to psig. Neglect change in air pressure.

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: Expandable pattern is used in ?

A:

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Metal forming processes are the processes in which plastic deformation of the material is done in…

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

A:

Q: 2. Sharp notches are often added to plastic food packages to help open them (along with arrows…

A: Detailed explanation:Sharp notches are a very good example of the functional features to the plastic…

Q: 2. Write 5 details found on the drawing title block?

A: The bottom right hand corner block in engineering drawing sheet is known as title block. This block…

Q: In Figure below, the main issue is with the leader representing which item?

A: Given:- An engineering drawing To find: Which representation is wrong

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: What do you mean by method of section?

A: Methode of the section is used to solve the static equilibrium of the strusses. In this method,…

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

A:

Q: 1.Forging is a process that uses application of force to give shape to metal.

A: Forging is a process that uses application of force to give shape to metal. Answer: True

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: In which of the following casting process, the melting pot is an integral part of the machine. * O…

A:

Q: how would i do the Chamfering for this part on the lathe? what cutting tool would i use  what…

A: Given drawing:

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: Open-die forging (upsetting) involves reduction of height of a specimen between two flat dies using…

A: Forging is the forming process in which metal is shaped by applying force using hammer or…

Q: short notes on any two types of chips formed during metal cutting operation

A: Metal cutting is defined as "the act of eliminating undesirable material from a block of metal in…

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS…

A: I have attached the image belowExplanation:

Q: A mandrel or steel rod is used to produce in drawing process.

A: Solution:

Q: What type of lines can be used in a drawing to show that part of an object has been removed ?

A: Solution : There are two types of line which are used to show the removed part of an object : Break…

Q: If rods of these materials are the same size, select the lightest metal rod. Titanium Carbon…

A:

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: Which one of the following material has the sheet metal applications O a. Mild steel O b. Cast iron…

A: Sheet metal is metal forming process which is used for forming into sheets

Q: what is the bottom length?

A: To calculate the bottom length

Q: What is compound indexing?

A: Soln:- Compound indexing :- Compound indexing is the operation of obtaining a desired spindle speed…

Q: I need answers to parts 7, 8, and 9, pertaining to the print provided.

A: What is the basic height of this assembly as shown in the section view?Refer the front section…

Q: The deep drawing blankholder is used in order to avoid defects of the flange which are named O a.…

A: b. The deep drawing blank holder is used to avoid wrinkling defect

Q: In charpy test specimen, the angle of v-notch section is_- O a. 60 degrees O b. 30 degrees O c. 90…

A: In the Charpy test, we measure the toughness of the material.  The angle of the V notch is 45 degree…

Q: Describe the method of sections?

A: Method of section In this method we deal with the non-concurrent forces. Here, we get three…

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in..     7.80…

A: The standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in. are: 7.80 in. 7.95 in.…

Q: Q1/B) Match between Column A & B. A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical…

A: To match: The column A and B. Given: Cutting fluid also known as emulsified oil. 1. Cutting fluid…

Q: Note 1 indicates 10 GAGE 1010-1020 sheet metal can be used to make the main body of this part…

A: Tolerance is the difference between the maximum size and the minimum size of the part or element.

Q: Replace the loading by an equivalent resultant force. Suppose that w₁ = 2 kN/m and w₂ = 5.5 kN/m.…

A:

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: What is the sliding block?

A: To Define: Sliding block

Q: This was not correct may you please

A:

Q: 6. How large of a square may be milled on the end of a 2 1/2-inch bar of round stock? Page #

A: The largest square that can be milled on the end of a 221​inches bar of round stock would have sides…

Q: How many auxiliary views of the print

A: Auxiliary Views:- When an object has a inclined surface, it is not possible to show inclined surface…

Q: How would a small or tight tolerance affect the layout?

A: The lines that are used for locating the points on the objects and items for the purpose of cutting,…

Q: I need these 3 parts answered TRUE or FALSE.

A: During the life of any product, parts used for many years are replaced to improve the efficiency or…

Q: the various parts? 13. What is the tolerance on "F," the chamfer angle? 13 14. How square must the…

A: 13. 6 ° is the tolerance on "F" the chamfer angle As 20° - 14° = 6°    14. square must the ends of…