20. Two horses on opposite banks of a canal pull a barge moving parallel the banks bymeans oftwo horizontal ropes. The tension in these ropes are 200 kN and 240 kN, while the anglebetween them is 600. The magnitude of the resultant pull on the barge will be: 29. In the figure below, the reactions at A and B are;A) Ra = 14 kN & Rb = 22 kNB) Ra = 22 kN & Rb = 14 kN.C) Ra = 18 kN & Rb = 20 kN.D) Ra = 14 kN & Rb = 8 kN.8 kN/mAB3 m3 m

Answered: Image /qna-images/answer/516654be-2cb5-477a-bf50-76ad773ccebb.jpg

Answered: nks of a canal pull a barg

Engineering

Civil Engineering

nks of a canal pull a barg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute the moment of inertia for the built up section shown below about the strong axis only.
How many minutes you took Name: to solve this problem? ID.: Section : HW-2 Replace the loading by an equivalent resultant force and determine where its line of action intersects post AB measured from B. 0.5 m B. 500 N 1m 02 m 250 N 30 1m 300 N
Questions T 40 mm TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C₁ C₂ 1.0 0.208 0.1406 1.2 0.219 0.1661 60 mm 1.5 0.231 0.1958 2.0 0.246 0.229 2.5 0.258 0.249 3.0 0.267 0.263 4.0 0.282 0.281 5.0 0.291 0.291 N 10.0 0.312 0.312 0.333 0.333 1. Determine the largest torque T which may be applied to end of the solid bar which is shown in the diagram above, knowing that the maximum allowable shear stress = 107 MPa and G = 40 GPa. Provide the answer in kNm with precision to two decimal points. 2. The same solid bar is subjected to a torque of 1.5 kNm. Its total length, denoted as z, is 601 mm. What will be the angle of twist? Provide the answer in degrees with precision to two decimal points.
With the aid of sketch, discuss the differences of functions of pipe in series andparallel. ?
Find the question, thanx.
人工知能を使用せず、すべてを段階的にデジタル形式で解決してください。ありがとう SOLVE STEP BY STEP IN DIGITAL FORMAT DON'T USE CHATGPT Design the longitudinal steel and the cross section of the beam shown, consider concrete that indicates fy = 4200 kg/(cm²), 1/2 stirrups and 2.5 cm coatings. 1m 0.5T 2m 0.2T 6.5m Calculate top rods per steel (min) asmin If f'c = 200kg/cm² 1.5T/m
Q. Finol the area of the field as shoos In figure A wth olistarces measured In feet between Vanious Points atkcked tigure A DISTANCES 1-2 = 75.32 4 2-3 = 5구.구9 3-4 = 55.38 3 4 - 1 = 60-41 1-3 - 83-4나
Date: A 60 cm square gate has its fop edge 12m belaw the water surfa ce. It is on g 45 ang le and iHS bottom edge is hinged as Shown in figure below . What for ce P is needed to just open the gate ? hes 0CM 1 8. 10 water ACH 45°
ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LNG EXPLANATION. ANSWER IN 2 DECIMAL PLACES.) 9.29 As a round log passes through a sawmill, two slabs are cut off, resulting in the cross section shown. Calculate Ix of the cross section if h = R/2. What is the percentage reduction in Ix caused by the sawing operation?