nat the purpose of the indicator is I the culculated value of the molarity of the NaOH solution be too high or too low hanged if the following errora were made? Explain your answeni. - beaker into which the student poured the NaOH solution from the fumo hood i some distilled water in it flask into which the student weighed the KHP wus wet

nat the purpose of the indicator is I the culculated value of the molarity of the NaOH solution be too high or too low hanged if the following errora were made? Explain your answeni. - beaker into which the student poured the NaOH solution from the fumo hood i some distilled water in it flask into which the student weighed the KHP wus wet

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

How do I calculate the molarity of the final solution?
4. A titration flask contains 0.00425 moles of an acetic acid sample a. Determine the moles of the base (NaOH) required to completely neutralize the acid. F b. If the molarity of the based added from the buret was 0.200 M, determine the volume of the base (in mL) required to reach the end point of this titration. Type here to search O нсд a 69002 BEST "l' X PASSANTEsser 14635 IS 20% 40 css 196 NG Info W
How many millilitres of 0.157M nitric acid are rrequired to neurtralize 22.1ml of 0.194 M sodium hydroxide?
The steps for determining the concentration of a sample of hydrochloric acid are listed below :Step (1): A 0.1038 M standard sodium carbonate solution was prepared by dissolving 2.750 g ofanhydrous sodium carbonate solid in deionised water and made up to 250.0 cm3.Step (2): 25.0 cm' of the standard solution obtained in Step (1) was transferred to a clean conical flask andthen a few drops of methyl orange were added.Step (3): The sample of hydrochloric acid was put into a burette. The standard solution in the conicalflask was titrated with the hydrochloric acid.Step (2) and Step (3) were repeated for several times. The table below shows the results of the titrations:Trial I 2 3 4Final burette reading/ cm330.85 28.75 28.30 31.35 27.25Initial burette reading/ cm32.00 1.50 1.00 3.00 0.00(a) Describe the procedure in preparing the standard sodium carbonate solution in Step (I). (b) State the colour change at the end point of the titration. (c) Calculate a reasonable average for the volume…
You mix aqueous solutions of 100.0 mL 1.70 M NaCl and 75.o mL 1.20 M Pb(NO3)2, calculate the mass of of precipitate formed.
added. The sample requires 34.47 mL of 0.485 M NaOH to reach the equivalence points. What is the mass of the oxalic acid (diprotic acid) in the sample and what is its mass percent? (0.753 g 6. A 1.034 g sample of impure oxalic acid (H2C2O4) is dissolved in water and acid-base indicator CHM 1045 Unit 3: Solutions/Redox/Gas 72.8 %) 5008.2-22 oressure of S0 will be the preseie
6. 20 grams of marble chips were placed i flask. Which one of the following would you allo. obtain 100 ml. of carbon dioxide as quickly asperu RC sible? A) 20 mL of 1 M HCI B) 40 mL of 1 M HO C) 30 ml. of 1.5 M HCI- D) 20 mL of 1.2 MB E) 40 mL of 2 M HCI
How many in 45mL of a ReOM HN n mdes of solute are containeal 0.3 Solutor
Q7) The indicator that is used for Vitamin C analysis is. a) Phenolphthalein b) 1₂ c) Starch d) KI
Could you please write me a brief summary about the results that I have and it's about the standardization of sodium hydroxide thank you
cacoH)2 a 15L he molarity of Our created Bi3 grams of is dissolved to create solution.calulate T solution
. So, we need 5.00 mmol of base (titrant) to be delivered to the analyte. Since we know the molarity of the base and moles of base, we just need to solve for the volume of base (titrant) to be added. molpase Mpase = Voladded Molarity base =. 0.150 (M) Moles of base = _5.00 (mmol) Volume of base needed to reach equivalence point _ (mL)