NaOH (aq) + HCI (aq) NACI (aq) + H2O (1) Volume of 1.00M HCI (mL) 45.0 Volume of 1.00 M NAOH (mL) 50.0 Initial Temperature ("C) 22.1 Final Temperature ("C) 31.6 la) Calculate the moles of HCI used in the reaction. Moles of HCI = mol (b) Calculate the moles of NaOH used in the reaction. Moles NaOH= mol (c) Which reactant is the Limiting Reactant, HCl or NaOH? Limiting Reactant = (d) Is this acid-base neutralization reaction exothermic or endothermic? NOTE: DO Include the correct number of significant figures or you will be marked

NaOH (aq) + HCI (aq) NACI (aq) + H2O (1) Volume of 1.00M HCI (mL) 45.0 Volume of 1.00 M NAOH (mL) 50.0 Initial Temperature ("C) 22.1 Final Temperature ("C) 31.6 la) Calculate the moles of HCI used in the reaction. Moles of HCI = mol (b) Calculate the moles of NaOH used in the reaction. Moles NaOH= mol (c) Which reactant is the Limiting Reactant, HCl or NaOH? Limiting Reactant = (d) Is this acid-base neutralization reaction exothermic or endothermic? NOTE: DO Include the correct number of significant figures or you will be marked

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The solubility product for the dissociation of Mg(OH), is 9 x 10-12. Determine the concentration of Mg2- and OH at equilibrium, expressed as milligrams per litres of CaCO3.
(i) For a waste water, the BOD, at 20°C is found to be 200 mg/l. What will be BOD, at 30°C for the same? The reaction constant 'K' (to the base e) at 20°C is 0.2 per day.
A Haldane modification of the Monod reaction is often used to describe the kinetics of substrate utilization when the substrate itself is toxic at high concentrations (phenol is an example of this). (1) Calculate the effluent concentration for a substrate exhibiting Haldane kinetics from a CSTR (continuously stirred tank reactor) and (2) compare this with the value if the substrate were not inhibitory (S2/Ki = 0) for the following conditions: V = 24 m3 Q = 9 m3/d S0 = 400 mg/L Y = 0.5 mg/mg q = 7.5 g/g•d K = 7 mg/L b = 0.1 d-1 Ki = 15 mg/L Hint: θx = (active biomass in the system)/(production rate of active biomass) = V/Q And 1/θx = (YqS)/(K + S + S2/Ki) – b
Choose the correct answer C3S has a faster rate of reaction accompanied by low heat generation. A-True B-False
A second-order irreversible elementary reaction 2A -> product is carried out in a batch reactor. It was found that it took 30 min for a reaction to reach 90% conversion. What would be the time required to reach the same degree of conversion if (a) the initial concentration of A was doubled, (b) the reaction rate constant was doubled, and (c) the reactor volume was doubled.
öalg äbäi is often described as the area of chemistry responsible for characterizing the composition of matter, both qualitatively (what is present) and quantitatively (how much is present). It was dealing with the identification and .determination of compounds
I need the answer as soon as possible
thermodynamics
Consider the equilibrium system described by the chemical reaction below. A 1.00 L reaction vessel was filled with 2.00 mol SO2 and 2.00 mol NO2 and allowed to react at a high temperature. At equilibrium, there were 1.30 mol of NO in the vessel. Determine the concentrations of all reactants and products at equilibrium and then calculate the value of Kc for this reaction. SO:(g) + NO2(g)= SO:(g) + NO(g) 1 2 NEXT Based on the given values, fill in the ICE table to determine concentrations of all reactants and products. SO:(g) NO:(g) SO:(g) NO(g) + + Initial (M) Change (M) Equilibrium (M) RESET +x -X 1.00 2.00 1.30 -1.00 -1.30 2.30 2.70 0.70 1.35 2.00 - x 2.00 + x Activa Go to Se 1L