Name three (3) type of water supply piping materials and respective type of connection joint used for distribution. a.

Q: Connection 1 2 Cannection 2 4 Rigid) siven 4 Types of Internal Connections (Moment release, Shear…

A: Connection1 :It shows shear release internal connection ,as there is the  transfers of shear forces…

Q: Distinguish between bearing type connection & friction type connection

A: The objective of the question is to differentiate between two types of connections used in…

Q: 8.a. Four electricians are discussing transformer installations. Electrician A says that there's no…

A: 8 (a) Electrician A is incorrect. This is because  there is a size requirement for the door sill of…

Q: What type of connection is made when the loads pass through the center of Gravity? O Bearing type…

A:

Q: Translate the following ads, and tell how many rooms each house probably has. 4br - 2 b - fam rm -…

A: given values- 4br - 2 b - fam rm - f/pl - din rm - 2-car gar - xlnt cond  120's - low CTM -…

Q: For the isometric below, find the following: 2 points for quantity and 1 point for hours 1. Linear…

A: Summary: Linear Feet of Pipe Install: 27.5 LF; Hours to Install: 71.5 MHDiameter Inch of Field Weld:…

Q: Reasons for using brass tube rather than solid brass rod?

A: It is required to answer the reasons for using brass tube rather than solid brass rod.

Q: match, options are in grey

A: Given Options: 300 Ibs pointed up300 Ibs pointed lefthorizontal load300 Ibs pointed down300 Ibs…

Q: If a bolt bears on a hole in a sawn timber beam or column, describe how the strength of the…

A: Tensile strength Tensile strength in the direction of the grain is usually 10-20 times more than its…

Q: 4) If a bolt bears on a hole in a sawn timber beam or column, describe how the strength of the…

A: The timber has many characteristics which is suitable in construction purposes. Timbers has high…

Q: hoose the letter of the correct answer. Pipe fittings are attached to the end of pipes to allow it…

A: The part which is attached to pipe is known as pipe fitting.

Q: A section of an OH line needs to be built on 46 ft. wood poles set 6 ft. deep in the ground. Each…

A: hag = Height of pole above ground = 46 - 6 = 40 fthbg = Height of pole below ground = 6 ft l1 =…

Q: EXAMPLE: Waterworks of a town treat 35 x 106 litres/day. The water is treated by…

A: Given data - Q = 35×106 L/day Consumed filter alum = 20 mg/L Alkalinity of water = 4.5 mg/L of CaCo3…

Q: Please give me right answer  Draw a flowchart on how to analyze a tension member, it's gusset…

A: The structural elements that are subjected to direct axial tensile loads and tends to elongate the…

Q: The efficiency of design using brass tube rather than solid brass rod?

A: The efficiency of design using brass tube rather than solid brass rod can be explained as follows:

Q: When is it necessary to full plank a scaffold platform? O Sec 130 (1)(a) O Sec 133 (2) O Sec 135…

A: Sec135 (1)(b) specifies the necessity of full plank of scoffolding platform to be provided if it is…

Q: 2. Based on the pressure of fluid on the submerged curved or flat plate, hydraulic gates are…

A:

Electrical Plans

An electrical plan is also known as an electrical drawing or a wiring diagram. It is a kind of visual representation which bears the blueprint symbols of all the electrical components in electrical house plans or various building construction projects. In other words, electrical plans describe electrical circuits and systems that build up the electrical house plans or building plans. An electrical engineer who works on various construction projects creates an electrical drawing. The engineer outlines the electric planning with different symbols and lines forming a detailed electrical circuit. These drawings are a means of representation for the clients, who will carry out the actual wiring process. In a nutshell, an electrical plan showcases the circuitry with the proper placement of electric components.