Name: Murtaza Ali Qasim Grop:B1 Q1/ Given, T- 24°c

Q: I have three parts that need to be answered pertaining to the print provided below.   What size…

A: Question:1The original version of engineering drawing sheet belongs to ISO A-series paper.

Q: Required information NOTE: This is a multi-part question. Once an answer is submittec Consider the…

A: P = 815 N

Q: Air contained in a piston-cylinder assembly undergoes the power cycle shown in the figure below. 3.0…

A:

Q: *6-120. The scissors hoist is operated by applying a Force P to the roller support C using a…

A: In the case of equilibrium sum of horizontal forces is the sum of vertical forces is zero and the…

Q: Draw digitally a unique, original design of a decorative block. Please refer to the sample picture…

A: A decorative block can be any type of block or object that is used for ornamental or aesthetic…

Q: *4-100. If the resultant couple moment acting on the triangular block is to be zero, determine the…

A: If the resultant couple moment acting on the triangular block is to be zero.Determine the magnitudes…

Q: Two 2 kg balls are attached to the ends of a rod. The rod is attached to an axle such that the balls…

A:

Q: 11) Define the cornering stiffness.

A:

Q: 4.) Determine the moment (scalar value) about axis AB from the cable tension force (T) exerted at…

A:

Q: HT-19-8: Consider a gas-filled cubic room (edge length: 1 m, wall temperature: 600°C, gas…

A: Write the heat transfer equation.Here,q = net radiative heat flow rate (Watts)σ = Stefan-Boltzmann…

Q: 9-38 Determine the work potential of a 13-m-high tide in kWh for an area of 1000 m². Take the…

A:

Q: 1. Steam is generated at 4.1 Mpa and 440 °C and condensation occurs at 0.105 Mpa. For a Rankine…

A: Given:P1=4.1 MPaT1=440°CP2=0.105 MPaWnet=30,000 KW

Q: Part A If h = 340 mm, locate the centroid y of the cross-sectional area of the built-up beam.(Figure…

A: h=340 mmTo determine:The centroid

Q: A forced draft fan is used to provide the combustion air requirements for a power boiler that burns…

A:

Q: With an increase in the thickness of insulation around a circular pipe,heat loss to surrounding due…

A: Given that a circular pipe is insulated, Let t be the thickness of insulation, ri be the inner…

Q: Match the parts of a print to the terms below.

A: Choice H is the Scale of the drawing of the part on the print sheet.

Q: Determine a general expression for the normal force NA exerted by the smooth vertical wall on the…

A: The mass of cylinder is .The mass of bar is .

Q: Figure -3 ft Figure -3 ft- < 1 of 1 M The bent rod is supported by a smooth surface at B and by a…

A:

Q: In (Figure 1), the tension developed in cables AB and AC cannot exceed 450 lb. Part A Determine the…

A:

Q: F2-1. Determine the horizontal and vertical components of reaction at the pins A, B, and C. -2r B 60…

A: Reaction at A is HA and VA similarly, reaction at C is Hc and VC Taking moment about point A…

Q: The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is…

A:

Q: Subject Engineering; textbook "AutoCAD and its Applications"  1- What is a drawing template? 2-…

A: 1. Drawing Template :-  The drawing Template file in AutoCAD is a drawing file that has been saved…

Q: An object of mass 4 grams hanging at the bottom of a spring with a spring constant 5 grams per…

A:

Q: Consider the yellow region that is bound by two straight lines and a circular arc in the xy-plane.…

A:

Q: Required information Blocks A and Beach have 5.5 kg mass. All contact surfaces have the same…

A: Blocks A and Beach have 5.5 kg mass.All contact surfaces have the same coefficient of…

Q: Osite figure a. Determine the area (in mm?) of the shaded part of the figure shown. 100 mm b.…

A:

Q: If the brake ABC is applied such that the magnitude of force P varies with time as shown, determine…

A:

Q: Thank you for the answer. but sir/ma'am it's kind of blurry can you do something about it if no,…

A:

Q: Figure Q1 (b) shows plane to be treated as a particle moving along the path of cquation y = 0.4x. At…

A:

Q: The circular disk of radius r = 0.25 m rotates about a fixed axis through point O with the angular…

A: The angular velocity is .The angular acceleration is .The radius is

Q: 1-90 A hydraulic lift is to be used to lift a 1900-kg weight by putting a weight of 25 kg on a…

A: NOTE -: Under the guidelines, we experts cannot include names in the answer.

Q: What is the specific volume of R-134a at 20°C and 710 kPa? What is the internal energy at that…

A: The temperature of R-134a is .The pressure of R-134a is

Q: Q#4: | 1) Define a line. What is meant by projection? 2) AB is at a distance of 5 cm in front of VP…

A: Engineering graphics is the study of representing a point, line or an object of three dimensional…

Q: 8. Find the first moments of area and centroid of the following shape of uniform density. The circle…

A: The radius of cricle is

Q: In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of…

A:

Q: 3.4-4 A solid circular bar ABC consists of two segments, as shown in the figure. One segment has…

A:

Q: Using the method of composite figures, a. Determine the total length (in mm) of the figure shown. b.…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.