Hello Sir,Good Night.I have a question in my homework related Heat Transfer lesson. The following below is my question. Please Advice. Thank You Carbon iron ball (p= 7833kg54.°C , Cp = 0,465.°C) has a diameter of 8kg,km3mm. The ball initially has a temperature of 900°C, Then, the ball is cooled through theannealing process at an ambient temperature of 35°C. The final temperature of the ballafter the annealing process is 100°C.If the convection coefficient between the sphere and its surroundings is 75W°C , thenhow long does it take for the annealing process?m2

Answered: Image /qna-images/answer/69e1be36-8aec-41db-b421-b08258c17c6b.jpg

n iron ball (p 7833 ,k = 54. °C , Cp = 0,465.°C) has a diameter of 8 m3 kg m he ball initially has a temperature of 900°C, Then, the ball is cooled through the ling process at an ambient temperature of 35°C. The final temperature of the ball he annealing process is 100°C. convection coefficient between the sphere and its surroundings is 75 .°C , then m2

n iron ball (p 7833 ,k = 54. °C , Cp = 0,465.°C) has a diameter of 8 m3 kg m he ball initially has a temperature of 900°C, Then, the ball is cooled through the ling process at an ambient temperature of 35°C. The final temperature of the ball he annealing process is 100°C. convection coefficient between the sphere and its surroundings is 75 .°C , then m2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3) Spray transfer takes place when O High current is applied and argon gas is used for shielding Low current is applied and argon gas is used for shielding High current is applied and helium gas is used for shielding Low current is applied and helium gas is used for shielding
QUESTION 2 Figure 2 shows an ima ge of a house located near to a lake, further away from a windmill. Passive cooling also known as one of renewable resources. House Lake Wind mill #196347897 { Image courtesy : https://adobe.ly/3130M17) Explain in brief the difference between passive cooling and active cooling in the context of renewable energy. Include list of reference in your submission (Wikipedia are not accepted). а. b. Based on Figure 2, show how it is possible to implement passive cooling for the house. In your answer, justify for every decision taken such as: i. Location of input source ii. Location of out put source ii. Method to improve the air flow
A child opens the door of the freezer that is turned off, to observe its operation. If the ambient temperature is 30°, what will be the behavior of the internal temperature of the freezer when it is opened and why? a. does not change, since there is no material between the environment and the interior of the freezer for heat exchange b. is increasing, because the convection between the environment and the air inside the refrigerator does not transfer heat from the outside to the center c. does not change, since there is no contact between the surface of the meat and the external environment d. increases, because sunlight falls on the meat, increasing the energy. Then, when turning on the freezer again, it is observed that the back of the freezer gradually warms up, and remains warm during the operation of the machine. The amount of thermal energy emitted by the freezer must be: a. equal to 0; the heating is due to a problem with the freezer b. Less than the energy drawn from inside the…
Hand wright no typing
d) Compare Young's modulus E (the stiffness property) and thermal conductivity (the heat transmission property) of aluminum alloys (a non-ferrous metal), alumina (a technical ceramic), polyethylene (a thermoplastic polymer) and neoprene (an elastomer). Which has the highest modulus Which has the lowest thermal conductivity? Lest you answer in a table Material 1- Young's modulus, E GPa T-conductivity . W/m.K 2. 3- 4-
PLZ MAKE ONLY SIMPLE EXPANATION FOR THIS QUESTION
Please help and show all steps on how answer was solved. Class is Heat Transfer. Thank you.
no previous attempt please
PLEASE ANSWER WITH COMPLETE AND DETAILED SOLUTION. THANK YOU
i need the answer quickly
PLEASE ANSWER QUICKLY
Please answer the given question and show the solution. Thank you very much! Note: Please include the units in the solution and use 4 decimals point in Final Answer.