A piston-cylinder device contains steam initially at 1 MPa, 450°C, and 3.0 m. Steam is allowed to cool at constant pressure until it first starts condensing. The figure shows the process on a T-v diagram with respect to saturation lines. Determine (a) the mass of the steam, (b) the final temperature, and (c) the amount of heat transfer.H2OQ1 MPa450°C

Answered: Image /qna-images/answer/ce5a4bc0-2b29-4fcd-a1c2-0b1505ab4b18.jpg

n-cylinder device contains steam initially at 1 MPa, 450°C, and 3.0 m. Steam is allowed to cool at constant pressure until it first starts condensing. The figure shows the process on am with respect to saturation lines. Determine (a) the mass of the steam, (b) the final temperature, and (c) the amount of heat transfer.

n-cylinder device contains steam initially at 1 MPa, 450°C, and 3.0 m. Steam is allowed to cool at constant pressure until it first starts condensing. The figure shows the process on am with respect to saturation lines. Determine (a) the mass of the steam, (b) the final temperature, and (c) the amount of heat transfer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Propane (MW = 44 ; k = 1.13) initially at 30 psia and 215°F, is stored inside a large spherical vessel having a diameter of 10 ft. If the temperature is increased to 635°F. Determine the following: - Constant Volume Specific heat in BTU/lbm.R - Change in Internal Energy, AUU in BTU
A piece of steel of mass 0.9 kg has a temperature of 95°C. It is immersed in a copper calorimeter which contains 0.45 kg of water at a temperature of 20°C. The final temperature of the calorimeter system, after cooling correction had been taken into account, became 32°C. If the specific heat capacity of steel is 480 J/kgK and that of copper is 394 J/kgK, determine the water equivalent of the calorimeter system.
Label steps clearly
A rigid tank of volume 2.5 m3 contains 15 kg of moist water vapor at 75°C. The water is then slowly heated. Determine the temperature at which the liquid, which is part of the wet vapor, in the tank evaporates completely. Determine the change in internal energy of the system. Also describe the process on a T-V diagram with respect to the saturation lines.
Saturated water vapor is contained in a rigid container. Heat is then added until the the pressure and temperature become 159.6 kPa and 400 °C, respectively. What was the initial temperature of the steam? °C
ReadSpeaker webReader: Listen In a reservoir, the pressure of a compressed gas must not be increased past 825 kPa. The gauge indicated 388 kPa when the temperature is 24oC. Determine the maximum temperature which can safely be attained in the reservoir
hi, can you solve this question ? The A and B tanks given in the figure are separated from each other by the closed valve between them. The water vapor in tank A has a volume of 0.2 m3, a temperature of 150 ° C and a pressure of 100 kPa. Tank B is filled with saturated water vapor in a volume of 0.3 m3 at a pressure of 300 kPa. Then, the valve between the tanks is opened and the final pressure is 175 kPa as a result of the mixing of the fluids in the tanks with each other and sufficient heat transfer. According to this:a) Temperature (C) and phase of the fluid in the final state;b) Find the amount of heat transfer in the process result.
Water is to be boiled at sea level in a 30-cm-diameter stainless steel pan placed on top of a 3-kW electric burner.If 51 percent of the heat generated by the burner is transferred to the water during boiling, determine the rate of evaporation of water. Please give your answer in kg/hour.
The water was heated up until the temperature is 200C. At this time, a pressure regulating valve installedat the top of the piston was activated which allowed the escape of saturated vapor at the same pressure.The application of heat was continued until the water quality is 100%. Determine the total heattransferred to the system in this experiment.
A 752-cm sample of water was placed in a 1.00-kg aluminum pan. The inital temperature of the pan was 26°C and the final temperature of the system was 39°C. What was the initial temperature of the water?
the initial temperature (T1) in (oC) is A piston-cylinder device contains water of quality x = 0.7 and pressure 200 kPa with an initial volume of 100 Liter. The system is now heated in isobaric process to a final temperature of 200°C. Piston-cylinder device water, x₁ = 0.7 P₁ = P₂ = 200 kPa Q₁2V₁ = 100 Liter T2 = 200 C
A rigid tank contains 10 kg of water at 90°C. If 8 kg of the water is in the liquid form and the rest is in the Vapour form, determine (a) the pressure in the tank and (b) the volume of the tank.