MULTIPLE ACCESS PROTOCOLS: COLLISIONS Consider the figure below, which shows the arrival of 12 messages for transmission at different multiple access wireless nodes at times t = <0.1, 0.2, 1.6, 1.8, 1.9, 2.1, 2.5, 2.8, 3.2, 3.7, 3.9, 4.8> and each transmission requires exactly one time unit. t=0.0 Answer t=1.0 • t=2.0 Į : t=3.0 ; t=4.0 QUESTION 1 OF 2 Suppose all nodes are implementing the Aloha protocol. For each message, indicate the time at which each transmission begins. Separate each value with a comma and no spaces. t=5.0

MULTIPLE ACCESS PROTOCOLS: COLLISIONS Consider the figure below, which shows the arrival of 12 messages for transmission at different multiple access wireless nodes at times t = <0.1, 0.2, 1.6, 1.8, 1.9, 2.1, 2.5, 2.8, 3.2, 3.7, 3.9, 4.8> and each transmission requires exactly one time unit. t=0.0 Answer t=1.0 • t=2.0 Į : t=3.0 ; t=4.0 QUESTION 1 OF 2 Suppose all nodes are implementing the Aloha protocol. For each message, indicate the time at which each transmission begins. Separate each value with a comma and no spaces. t=5.0

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

In the following schematic of a network each letter is a router. You have four packets to send. Each packet is 1Mbit. Assume processing delay is zero.     A ------------- B --------------- C     Assume that data travel with the speed of light from A to C. Assume that A is in LA, B in NY and C in Central Europe. The distance from A to B is approximately 4.5 million meters and the distance from B to C is 6 million meters. 1. Assume transmission rate is R=100Mbps for link AB and R for link BC. In other words, link BC has exactly the same transmission rate as link AB. a. When will each packet arrive at C? State your answer in ms for all questions. b. What is the average queuing delay at A? c. What is the average queuing delay at B?  2. Assume now that transmission rate for AB is R=100 Mbps but transmission rate for BC is 20 Mbps. a. What is the average queuing delay at A? b. What is the arrival time at router C of each of the four packets?
the packet size is 8 Bits. There are 5 routes between the sending host and the receiving host. each link has a transmission rate of 1 Mbps. sUPPOSE THAT ALL ROUTERS USE STORE AND FORWARD PACKETS SWITCHING. Assuming zero propagation delay. determine total end to end delay to send 5 packet
Suppose a single 802.11n client is connected to an 802.11n access point and there is no other client or access point in the neighborhood. The client senses the medium, then sends an 1,147-Byte frame, and waits for an 169-byte acknowledgement from the AP, and then repeats the process. The data rate on the wireless link is 400 Mbps. Assume DIFS=44 μs and SIFS =15 μs, no propagation delay and no error. Calculate the throughput for this client in Mbps. Calculate up to 1 decimal point.
Given what we know about transmission delay and the following: A web client and a web server separated by one intermediary router. • Each link carries data at 1Mbps with an MTU of 8192 bytes • Each link is 1000 km long with a propagation speed of 250000 km/s • Zero processing and queueing delays • Connection management packets (packets used for opening a connection, confirming a connection and acknowledging receipt of information) contain no data and all packets have 125 bytes of overhead on top of any data they may contain. • The web client makes an HTTP request to the server that is 250 bytes long. • The requested data is 4 kilobytes in size with 500 bytes of overhead for the HTTP status and headers What is the RTT to open the connection? а. b. How long would it take for a web client to complete the request? You can ignore any time needed to close the connection.
In this problem you will be doing some elementary calculations of transmission and propagation delays. Consider two hosts, A and B that are connected by a transmissions link of2.1 Mbps. Assume that packets are of length 2.0 Kb (Kilobits) and the length of the link is 100Km. Suppose now that that length of the link is doubled. What is the propagation delay from A to B now and what is the transmission time?
Ethernet is a distributed LAN protocol, which means that there is no centralized control node, and therefore a single node's failure will never bring the whole network down. However, can you see any advantage in establishing a centralized LAN in which a single node is in charge of the whole network and determines who receives messages and who waits? Explain.
Consider a router that transmits bits onto a transmission medium at the rate of 2 Mbps. Let the link be 3 km in length, and bits propagate through the transmission medium at the speed of (approximately) 3x10^8 meters/sec. What is the transmission delay in seconds to transmit a packet of size 2,0o0 bits onto the link? a. 1x10^-5 seconds O b. .001 seconds с. 1 second d. -4 seconds
Suppose a single 802.11n client is connected to an 802.11n access point and there is no other client or access point in the neighborhood. The client senses the medium, then sends an 1,337-Byte frame, and waits for an 132-byte acknowledgement from the AP, and then repeats the process. The data rate on the wireless link is 400 Mbps. Assume DIFS=47 μs and SIFS =11 μs, no propagation delay and no error. Calculate the throughput for this client in Mbps. Calculate up to 1 decimal point.
A router output port is being dimensioned to support a mean packet arrival load of 100 packets per second where the mean packet length is 500 bytes. Determine the minimum output link capacity such only 10% of packets experience a delay greater than 15 ms. Select one: O a. 1.2 Mb/s O b. 4 Mb/s Oc. 1 Mb/s O d. 0.5 Mb/s O e. 0.8 Mb/s
Consider the scenario shown below, with 10 different servers (four shown) connected to 10 different clients over ten three-hop paths. The pairs share a common middle hop with a transmission capacity of R = 200 Mbps. Each link from a server has to the shared link has a transmission capacity of RS = 25 Mbps. Each link from the shared middle link to a client has a transmission capacity of RC = 50 Mbps. What is the maximum achievable end-end throughput (in Mbps, give an integer value) for each of ten client-to-server pairs, assuming that the middle link is fairly shared and all servers are trying to send at their maximum rate? Group of answer choices 200 Mbps 20 Mbps 275 Mbps 25 Mbps 50 Mbps
not handwritten A server sends packets to a client via satellite. The packets must traverse one or multiple satellites before they reach their destination. The satellites use store-and-forward packet switching, with a switching time of 100 μsec. If the packets travel a total distance of 29,700 km, how many satellites do the packets have to pass if 1% of the delay is caused by packet switching?