millan Learning A chemist samples a river's water to measure the amount of fertilizer runoff from the area farms. In a 0.0950 L sample, the chemist measures 439 µg of nitrate. Express the concentration of nitrate in parts per million (ppm) and parts per billion (ppb) Assume the density of the river water sample is 1.00 g/mL.

millan Learning A chemist samples a river's water to measure the amount of fertilizer runoff from the area farms. In a 0.0950 L sample, the chemist measures 439 µg of nitrate. Express the concentration of nitrate in parts per million (ppm) and parts per billion (ppb) Assume the density of the river water sample is 1.00 g/mL.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

For the following, use proper sig figs, do not include units, and do not place numbers in scientific notation. A simple equation that can be used ONLY for dilutions is M1V1 = M2V2. So if a concentrated solution starts out as 1.36 M and you wish to make 50.0 mL of a 0.286 M solution, how many milliliters of the concentrated solution do you need? How much water will you add?
1. A 4.24 g sample of a laboratory solution contains 1.42 g of acid. What is the concentration of the solution as a mass percentage? 2. Isopropyl alcohol is mixed with water to produce a solution that is 35.0% alcohol by volume. How many milliliters of each component are present in 645 mL of this solution?
A stock solution of 14.5 M nitric acid (HNO3) is available to you. You have been told to make a 3.45 M dilute solution of nitric acid (HNO3) using 25.0 L of the stock solution. What is the maximum volume in L of the dilute nitric acid solution (HNO3) that you can make?
Lead is a possible contaminant in public water systems. There are many reasons we should be concerned about this, but this may be especially concerning if the water is used for drinking. Removing all lead is not feasible, so many local governments must set an “acceptable” concentration for contaminants. The “acceptable” concentration of lead in public water for some states is 7.2 x 10^-7 M. If 10.00 mL of 1.00 M lead is poured down the sink, how many liters of water are required to make sure the concentration of lead is 7.1 x 10^-7 M, which is just below the acceptable level?
Part 1: 8.132g of Mg(NO3)2 are dissolved in 950.0 mL of water. Calculate the molarity of the Mg(NO3)2 solution. Part 2: Calculate the molarity of a solution made by dissolving 2 g of glucose in sufficient water to form exactly 50 mL of solution. Part 3: If 55 grams of Barium nitrate were added to water to make a solution of 250 mL what owuld be the molarity of the resulting solution.
You need to make a 0.64 L solution of Mg(NO3)2 that has a nitrate concentration of 0.829 M. What mass of Mg(NO3)2 is required? Report your answer in SI units
I'm stuck on a homework question. Any help would be great
Consider a solution prepared by combining 45.0 g of BaCl2 with enough water to prepare a 750.0 mL of solution. Assume that the volume of water added was 748 mL. Density of water is 1.00 g/mL. 1) What volume of this solution would be required to prepare 500.0 mL of a solution that is 0.0034 M in BaCl2?
What volume (mL) of 12 M HCl was required to react with the Mg? The data I have for you is this: Mg+2HCl-->MgCl2+H2 is the chemical equation. The mass of magnesium is 0.0273 grams and the moles is 0.001123 The moles of HCl that were consumed in the reaction was 0.002246 moles With this data, I need to know how we can get the volume (mL) of 12 M HCl was required to react with the Mg?