Answered: Methods that prevent loss of moisture…

Methods that prevent loss of moisture from concrete by sealing the surface all .a Water proof plastics .b Use liquid membrane-forming compounds .C Forms left in place .d

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: i. How and why do we test ii. What does it tell us about the mix iii. What is expected to happen…

A: Compressive strength is a very important property of materials and structures. It measures the…

Q: Calculate the modulus of elasticity of fiberglass under isostrain condition if the fiberglass…

A: Given :- Fiberglass consists of 70% E- glass fibers and 30% epoxy by volume Modulus of elasticity…

Q: design a concrete mix to make 9 m3 of fresh concrete the concrete is located near the sea select the…

Q: Once in civil engineering, what is the minimum curing period typically recommended for concrete…

A: In civil engineering, the minimum curing period for concrete structures typically depends on the…

Q: Determine the (x, y, z) coordinates for the composite volume 130 mm Z 190 mm 275 mm 220 mm 190 mm…

A: A 3D structure is given. To determine the centroid x, y, z of the section. Steps- First, take 2D…

Q: choose the correct option please Silica fume admixture increase concrete strength up to 60 MPa 120…

A: This question is related to Concrete technology from Civil Engineering. In this question ask about…

Q: 61. The repair and rehabilitation of damaged or spalled concrete is done by removing the A. O Loose…

A: This question is related to the Concrete from Building Material.

Q: For the composite bar indicated, determine the permissible bending moment when the bar is bent about…

Q: 5 kg continuous boron fibers are introduced in a unidirectional orientation into 8kg aluminum…

Q: A fiber-reinforced polymer composite under isostrain condition consists of 35% fibers and 65%…

Q: Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The…

A: here m ,modular ratio is m = Esteel/ E another now , width of brass is 40/ mnow widht barss is 20mm…

Q: 10. if a composite bar is cooled,then the nature of stress in the part with high coefficient of…

Q: An epoxy (E=2.4 GPa) is reinforced with carbon fiber with module of elasticity equal to 260 GPa.…

A: The modulus of elasticity of the epoxy is Em=2.4 GPa. The modulus of elasticity of the fiber is…

Q: Determine if w12x14 (A36) section is Compact, Non-Compact or slender. Show neat handwriting and…

A: The given data is shown below: W12×14A36 steel

Q: Determine the product of inertia (lxy) for the composite

A: ###Product of Inertia Ixy about centroid axis x,y #####

Q: Name three functions of the matrix phase in fiber-reinforced composites. State the reason for the…

A: The material which has high strength / weight and also modulus/weight and has three components of…

Q: Hydration of cement is due to chemical action of water with * Gypsum Tricalcium aluminate and…

A: Option D is correct...

Question

Methods that prevent loss of moisture
from concrete by sealing the surface
all
.a
Water proof plastics
.b
Use liquid membrane-forming
compounds
.c
Forms left in place

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What are the two main reasons that steel corrodes inside reinforced concrete? ingress of chlorides from deicing chemicals carbonation that reduces the internal pH the use of a low w/cm concrete mixture increasing the cover distance over the reinforcing steel using silica fume to reduce the permeability of the concrete using corrosion inhibiting chemical admixtures
Q6) How does moisture impact tension and compression strength in composites?
An epoxy (E = 2.7 GPa) is reinforced with 70 vol% E-glass (E = 79 GPa). The fibres are continuous and aligned. Assuming no voids, compute the modulus of elasticity in the longitudinal and transverse (lateral) directions. Select one: a. Longitudinal modulus = 8.3 GPa, Transverse (lateral) modulus = 64.9 GPa b. Longitudinal modulus = 56.1 GPa, Transverse (lateral) modulus = 8.3 GPa c. Longitudinal modulus = 19.6 GPa, Transverse (lateral) modulus = 56.1 GPa d. Longitudinal modulus = 64.9 GPa, Transverse (lateral) modulus = 19.6 GPa
Define hardenability.
What will be the moment of resistance of the composite section shown in the figure below if the permissible stress in wood and steel is 70 N/mm² and 120 N/mm² respectively. Steel plate Wood -200 4150 400 10
Determine the total area of the composite figur e . (mm^2)Determine the x coordinate of the centroid of composite figure. (mm)Determine the y coordinate of the centroid of composite figure. (mm)
Concrete cover around the reinforcing steel is required in order to accomplish which of the following? Check all that apply. a. Mitigate wear and tear due to traffic b. Protect against corrosion of the steel c. Provide sufficient bond between the concrete and reinforcing steel d. Protect against strength loss due to fire
IV- It is necessary to design a continuous and aligned glass fiber-reinforced polyester having a tensile strength of at least 1400 MPa in the longitudinal direction. The maximum possible specific gravity is 1.65. Using the following data, determine whether such a composite is possible. Justify. Assume a value of 15 MPa for the stress on the matrix when the fibers fail. Material Glass fiber Polyester Specific gravity 2.5 1.35 Tensile strength (MPa) 3500 50
This refers to a change from liquid state to solid state of cement paste.
pls show me a solution.
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Taking h= 9 mm and using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Brass Aluminum 30 mm Modulus of elasticity Allowable stress h 30 mm h Aluminum 70 GPa 100 MPa The largest permissible bending moment is Brass 105 GPa 160 MPa 1.17 kN-m.
For the composite bar indicated, determine the permissible bending moment when the bar is bent about a vertical axis. Aluminum stress is 100 %3D MPa, Brass stress is 160 MPa, Eb = 105 GPa, Ea = 70 GPa Brass 6 mm Aluminum 30 mm 6 mm -30 30 mm