meter ab re the alcc ospheric E

Q: If the tension in the cable is F, determine the magnitude of the moment produced by this force about…

A:

Q: poad the aeasarement of the Micometer (b) 20 15 0-25 mm

A: Metrology Metrology is the branch of science which deals with the measurements. Metrology is the key…

Q: What means this equation T = My IG

A:

Q: If the frequency of a waveform is 50 Hz, then the time period of the waveform is O a. 0.2 msec O b.…

A:

Q: Consider a two-stage cascade refrigeration system operating between the pressure limits of 1.2 MPa…

A: Solution to A and B as mentioned by the student:

Q: A mass, m of 22 kg consider one vertical motion only with angular displacement, 0 = wt, with spring…

A:

Q: Petermine the displacement W= 0-589 J F = 0-3 N

A: Given data : Force=F Work done=W   Required : Displacement

Q: The venturimeter is a discharge measuring instrument. Select one: O True O False

A: Venturimeter is a device works on the principal of Bernoulli theorem, used in measuring flow rate or…

Q: How does a pressure control solenoid regulate transmission pressures? (50 - 80 words)

A: This question is based on the concept of pressure control solenoid.

Q: What is the measurement accuracy AND unity of the instrument in Figure

A: Accuracy of the Bourdon tube pressure gauge

Q: I need parts 7, 8, and 9 answered pertaining to the print provided.

A: Geometrical dimensioning & tolerancing (GD&T) is the system used for defining and…

Q: Define the pitch of Micrometre Gauge?

A: Micrometre gauge is an instrument which is used for measurement.

Q: Exja birak prah Sifid and BIMd- ? 6m t. Ay

A: Length of beam L=12 m Intensity of Uniform varying load w=6 kN/m Suppose Ay and By be the vertical…

Q: Fig. 9 6. Explicate the function and name of every instrument used in figure 9

A: To explicate: The function and name of every instrument used in figure 9. Explanation: The name of…

Q: What happen when input II (push button) is pressed. 11 Q1 () Q1 Q2 O a. Ql -1 Q2 0 Ob.Ql-1Q2 1 Oc.…

A: The correct answer for the above mentioned question is given below. I am pretty sure of the answer.

Q: The ratio of the amplitude of the output signal divided by the input signal in a static calibration…

A: In a static calibration, the ratio of the amplitude of the output signal divided by the input signal…

Q: E pelermine what Type of Alter shownn The figer batew fake .R=2k Conseder The S=JW L=2H and G2Mi

A:

Q: How can the metronome be used as a training tool for performance appraisal?

A: Metronome is a device which makes a a tick sound with the passage of time. It is generally used to…

Q: Nou Conformance t found wwle to paodu withim the po in Stiu r per

A: Given Data⇒ Product Cost

Q: Which one of these tables is least stable?

A: The answer for the given question is provided below.

Q: Construction of pressure gauge used for measurement of air pressure in tyres.

A: The pressure gauge is defined as the instrument or measuring device that is utilized to gauge the…

Q: The Pitot static tube is used to measure the dynamic head. Select one:

A: Given:To determine whether the given statement is TRUE or FALSE.

Q: how to read the vernier in inche? what is the reading in inch 1/128in 10 20 30 40

A: It is required to read the vernier

Q: Describe the operating principle of a Karman Vortex air flow meter used in some engine management…

A: A Karman vortex air flow meter (KVAFM) uses the principle of vortex shedding to measure the flow…

Q: Sketch a setup and measurement method that may be used to check the runout tolerance. Also show the…

A: To sketch a setup and measurement method to check runout tolerance. and to show acceptable max…

Q: Match the symbol to the component: а. Pump b. Motor c. Cylinder with retract cushion d. Pressure…

A:

Q: uid used in bourdon gauge calibration

A: The fluid used in bourdon gauge calibration is Used to transfer the pressure from weights to the…

Q: Which of the following flow meters is of positive displacement type? mass gas flow meter rotameter O…

A: Positive Displacement Meter: In this type of flow meter, the fluid mechanically displaces the…

Q: 39. A four-stroke compression ignition engine delivers 600 bhp of brake power output when running at…

A: Answer: The brake mean effective pressure is 120 psi.

Q: Respond with TRUE if the symbof of the valve shown below is drawn cortectly A 工 R Select one: O True…

A: True or False  The given symbol

Q: Q1 A single stage helical gearbox as shown in Figure Q1 is pulling a crate with an acceleration of…

A: Given: The acceleration of box, a = 1.5 m^2 The diameter of the drum, D = 1.2 m The transmission…

Q: Explain the working of Strain gauge type transducer with a neat diagram to measure the displacement.

A: Strain is a dimensionless quantity which is given by the ratio of an object's change in length to…

Q: the engine rpm is measured by measuring the current of an alternrator, driven by the engine…

A: the engine rpm is measured by measuring the frequency of an alternrator, driven by the engine

Q: How do integrate to get fbd= 15/28

A: It is asked to calculate the shear force in the section BD

Q: e Taylor's principle with Plug and Ring Gauge with figure.

A: The given problem is based on metrology.    Taylor's Principles: Go gauge should be design on…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.