How do integrate to get fbd= 15/28

Q: Determine pressure in [kPa] in the cylindrical pressure vessel shown, if the measured hoop strain is…

A: Given, εhoop=500×10-6E=70 GPa=70×109 Paμ=0.33Ri=400 mm=400×10-3 mmt=6 mm=6×10-3 mm Internal diameter…

Q: Use S = Last digit of your matric number and T= second last digit of your matric number. Example: if…

A: Given: S=2 , T= 0 To Find:  The enclosed area.

Q: la) If a 35 tonne block is raised to 110m and then falls to ground level (in generating mode) in 3…

A: 1a) Given         Mass, m = 35 ton = 31751 kg       Height, h = 110 m          Time, t = 3 min…

Q: The figure shows a linkage in one position. What is the instantaneous acceleration of point Pif the…

A:

Q: Please assist with this practice question 8. I don't know where to begin with this. Give details on…

A:

Q: 2 02 5 A 6 7 08 8 3 B с 9 4 D E

A: The J1 refers to the binary joints or the lower pairs in the given mechanism while J2 refers to the…

Q: For the beam and loading shown, determine the deflection midway between the supports. Assume that El…

A:

Q: Give all the location dimensions between the datum target points, B1 ,C1 and B2, C1. B1, C1 : X =…

A: Since, the bottom part of the drawing represents dimensions in X and Y direction while the upper…

Q: I’m a doing a stiffness compliance matrix. E_1 is 150 GPA; what are the units of E_1 when I do…

A:

Q: What type of scale is 10:1? O Full Scale O Enlargement Scale O Reduction Scale

A:

Q: Don't Use Chat GPT Will Upvote

A: Diagram-    Detailed Explanation of Reflection on a Curved Surface Understanding Key Concepts:1.…

Q: Write a program to get figure (2) from the figure (1) using transformation matrices and MATLAB form.

A: Given:To find:Write a MATLAB program.

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0  ,  Y =74   ,   Z =…

Q: Can you show all the mathematical steps to find Qd?

A: Given: The diffusion coefficient for carbon in BCC iron at 400C and 900C is given as 3.80x10-13 and…

Q: mechanical design and drawing

A:

Q: what is the omega value? as per the professor, the IC is at b not a

A: Given: The velocity of the upper wire: →V=5.6 m/s It is right that the instantaneous center of…

Q: Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and…

A: Volume for each action:Cyl. A extends DE = 65 cubic inCyl. A retracts DR = 62 cubic inCyl. B extends…

Q: Help me describe how you would create the slanted portion without using the Swept command in Siemens…

A: To create the slanted portion of the model shown in the image without using the Swept command in…

Q: How do you determine W(input)?

A: Coefficient of performance of reversible heat pump is defined as COPR,HP=THTH-TL…

Q: ead intrustions on example and help anwser it please and th

A: Jsolid Cylinder =πd432 DAC = 0.9 JAC =π 0.9432=0.064412467

Q: What company specification number is given to the material for this part?  2. What is the revision…

A: Engg drawing is a technical drawing that is used to transfer the information from the design to the…

Q: 187

A: Given:The rotational speed of the gear 2, The power transmission from the pinion gear to the output…

Q: Write the Compatibility Equations?

A: Compatibility Equations…

Q: Solidworks part Units: MMGS Primarily just need help understanding how to interpret the holes on…

A: It is asked to interpret holes to sketch them in Solidworks

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.