Mechanical services , i need solutions in 10 minutes please. MCQ/The heat transfer due to solar radiation through the window is given by .

Q: Critical damping of the system ?

A: Given: Mass,m=13.8 kgSpring stiffness,k =1365 N/mDamping coefficient=17 Ns/mCritical damping of the…

Q: A pulley used to transmit power by means of ropes has a diameter of 3.5 m and has 10 grooves of 45°…

A: Given data: d=3.5 mn=102β=45°=0.7854 radθ=160°=2.79 radμ=0.3T=1000 Nm=1.5 kg Need to determine the…

Q: Q.2) Draw the shear force and bending moment diagrams for the two distributed loads and two reaction…

A: To Find :  The shear force and bending moment diagram of beam . Free body diagram : Free body…

Q: A uniform rod AB of length L=900mm and mass m=4kg is suspended from a hinge at C. The distance from…

A:

Q: A car is travelling along a straight horizontal road with a constant acceleration of 0.75 m/s. The…

A:

Q: A water container is kept on a weighing balance. Water from a tap is falling vertically into the…

A:

Q: Q/ Find the number of steel bars for a rectangular foundation and support an interior column of…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Through what will body A move to in changing its velocity from 6 fps to 12 fps?  Don't forget to…

A: Consider the diagram as shown below for the given system. The increase in the height of the block B…

Q: 2. A gas absorber is fed, via stream F1. 100 mol/min of monoethanolamine (MEA) and CO2. Stream Fi is…

A:

Q: A rigid bar, hinged at one end, is supported by two identical springs as shown in figure. Each…

A:

Q: standard deviation of the resulting linear

A: Given data, Linear dimesnions,S and T are,  σs=7 μm  σT=12 μmCalculate the standard deviation of the…

Q: 2. Find all the axial forces on each member of the truss shown.

A:

Q: Material Aluminum Form Cylinder Diameter 12.8 mm Gauge Length 50.8 mm Tensile Testing To Failure

A:

Q: (1) A rod of length L has a small square cross section b²; the density of the material is p. Just by…

A:

Q: Find the Area Moment of Inertia about an x axis passing through the centroid (Ix) of the composite…

A:

Q: a). velocity at B, VB b) velocity at C, VC c)distance BC d)velocity at D, VD *

A: hete apply mechanical energy conservation principle. for solution refer below images.

Q: QUESTION 1 "An automobile, weighing 1100lb empty and 3200 lb fully loaded, vibrates in a vertical…

A:

Q: For the beam with shown loading, show that the equation of the elastic curve is Wo 7w,L3 + x3 y = EI…

A:

Q: Please include the FBD, I need solution asap

A:

Q: Calculate the force the biceps muscle must exert to hold the forearm and its load as shown in…

A: Consider the free body diagram shown below for the arm.

Q: 9. In order to make stress in AB segment of the rod how much temperature should be increased.

A:

Q: Q3: What are the priority operations for minimization and recycling of waste

A: Basically Waste is unwanted or which unusable and which provides harm to the environment. So it is…

Q: Determine the Grashof condition and Barker Classification for the following mechanism, if d = 0.1 m,…

A: The solution is provided below.Here P and Q are the rest two link other than the shortest and…

Q: Water is the working fluid in a Rankine cycle that produces 100O MW of power. Superheated vapor…

A:

Q: Q:In Figure, two blocks are connected by a solid strut attached to each block by a pin. If block B…

A: From the data given, Weight of the block B = WB = 100 N Fricition coefficient between block A and…

Q: 2-2 The sun gear-2 and -5 are integral with the input shaft of the compound epicyclic gear…

A: givensun gear 2 and 5 are integral part with the input shaft of the compound epicyclic gearannular…

Q: A (2cm) thick steel plate of thermal conductivity (50 W/m °C) has a uniform heat generation of (40*…

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 0.50 a Answer: (X, F) = ( i i…

A:

Q: I need , RAy and RBy with complete solution write it on a paper. Thank you for helping.

A:

Q: PROBLEM A vector B is 10 cm. Iong and has a direction – sense of 45°. Vector C is 15 cm. long and…

A:

Q: Refrigerant 134a enters a well-insulated nozzle at 200 lbf/in.2, 170°F, with a velocity of 120 ft/s…

A:

Q: 23. Given the below velocity triangie, having a blade angle of 29 the radial component. Va (mVs) is…

A: Given : To find : Radial component of velocity

Q: Distilled water with a mass flowrate of 80,000 kg/h enters an exchanger at 35 °C ane leaves at 25…

A:

Q: A beam of the cross section shown is made of a steel that is assumed to be elastoplastic with E= 200…

A:

Q: HW Ball ( A ) is released from rest at a height of ( 40 ft ) at the same time a ball ( B) is thrown…

A:

Q: F = 20 kN (note the 0.3 space at the end) The magnitude of the internal normal force at point C is…

A: given data; F=20KN w=8KN/m

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.