Match the Different Switch Port Modes with their definitions: Trunk 1. Forms an unconditional trunk. Dynamic Desirable II. Attempts to negotiate a trunk with the far end. Dynamic Auto Access III. Forms a trunk only if requested by the far end. IV. It will never form a trunk. QUESTION 9 VLAN 150 is not yet configured on your switch. What happens if you issue the switchport access vlan 150 command in interface configuration mode? a. The command is accepted and the respective VLAN is added to vlan.dat. O b. The command is rejected. O c. The command is accepted, and you must configure the VLAN manually. Od. The port turns amber.

Match the Different Switch Port Modes with their definitions: Trunk 1. Forms an unconditional trunk. Dynamic Desirable II. Attempts to negotiate a trunk with the far end. Dynamic Auto Access III. Forms a trunk only if requested by the far end. IV. It will never form a trunk. QUESTION 9 VLAN 150 is not yet configured on your switch. What happens if you issue the switchport access vlan 150 command in interface configuration mode? a. The command is accepted and the respective VLAN is added to vlan.dat. O b. The command is rejected. O c. The command is accepted, and you must configure the VLAN manually. Od. The port turns amber.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Execute the command to show the files that are needed for routing operation. Get theinformation about the various drivers and interfaces present in your PC.
On a 2960 switch interface, the command is used to configure a trunk port?
Can you create a port knocking system only with iptable commands that will open up port 22 (SSH) when the remote host “knocks” on ports 2222, 3333, 4444 within 30 seconds?
In case you are using DHCP (i.e. if the option “Automatically acquire an IP address” is chosen), try to get a new IP address. You can return the IP address back to the DHCP server by using the command ipconfig /release at the command prompt. You can obtain (renew) the private address using ipconfig /renew. Try these commands and explain what happened.
hi. which option is correct here?
Which parameter must be specified while redistributing a route into EIGRP? Administrative Distance Seed Metric Exit Interface Next Hop IP
As shown in the figure, the two switches use the default parameters to run STP. the configuration command STP root primary is used on switch A, and the configuration command STP priority O is used on switch B. Then which port will be blocked? МАС 0001-0203-04AA MAC 0001-0203-04BB Fr HUB m.com SWA SWB GO/0/2 S. GO/0/1 GO/0/2 GO/0/3 GO/0/1 GO/0/1 A. HUB's G0/0/3 B. GO/0/2 of switch A C. GO/0/1 of switch A D. GO/0/1 of switch B The output information of a certain device is shown in the figure. Which of the following statements is correct? (Multiple Choice) display interface GigabitEthernet 0/0/0 G1gabi tEtherneto/0/0 current state : UP Line protocol current state : UP Route Port, The Maximum Transmit Unit is 1000 Internet Address is 10.0.12.2/2 4 IP Sending Frames' Format is PRTFMT ETENT_2.Hardware address is 00e0- fc22- 4fff Port Mode: FORCE COPPER Speed: 100.Loopback: NONE Duplex: FULL.Negotiation: DISABLE Md1: AUTO Last 300 seconds input rate 24 bits/sec. O packets/sec Last 300 seconds…
What is the purpose of the listen() function in network programming? Question 9 options: To listen for incoming connections and queue them up for processing by the server To initiate a connection to a remote server To create a socket To accept an incoming connection request and create a new socket for communication with the client
To configure an OSPF in a single-area internetwork, use the following IOS command? ospf router id router ospf process-id ospf configuration id router process-id
Your DHCP server's configuration has been updated to include these new DNS servers. As a whole, what is the best way for your clients to get the new settings? * Perform a double restart of the computer. Enter ipconfig /registerDNS on the client. DHCP clients must wait for the lease to be renewed before continuing to use the network. O Input ipconfig /renew into the client's terminal. Clear the server's DNS cache.
Which of the following is not a standard flag used in TCP client-server communication? 1 point Start Synchronize Acknowledgment Finish
What is an APIPA? What is the relationship between DHCP server and APIPA? What are the DHCP scopes? What is the DOS command prompt to start the DHCP server? What is the DOS command prompt to stop the DHCP server? What is the DOS command prompt to pause the DHCP server? What is the DOS command to return the mac address of any clients from server? Is it possible for linux Os computers to take dynamic ip configurations from windows server? What is 80/20 Rule for Servers and Scopes? There are two versions of Network Monitor are available, what are there? What the differences between them? What is the WINs in windows server? In which partition of file system the DHCP configuration files store? What is the difference between network and Network-Manager servicS