Match the definition to that of the main word in specific context. Prompts Submitted Answers Process by which air within the voids between particles is replaced by liquid. Choose a match Granulation Initial step in combining primary solid particles with a liquid drop to form new granules or nuclei. Wetting Nucleation Question 10 The screen efficiency is A recovery + rejection B recovery rejection D None of these

Q: Briefly differentiate between total efficiency and grade efficiency for a  gas–particle separation…

A: To Briefly differentiate between total efficiency and grade efficiency for a  gas–particle…

Q: Discuss the following:1. The similarities and dissimilarities between wet scrubbing process and gas…

A: Wet gas scrubbers are devices that are used to remove a variety of pollutants from exhaust gas from…

Q: A process flow diagram of an anode fuel cell.

A: The process of creating a process flow diagram (PFD) for an anode fuel cell entails putting the…

Q: Make a comparison between thermoplastics and thermosetting polymers(a) on the basis of mechanical…

A: A resin that is solid at room temperature but becomes plastic and soft upon heating is a…

Q: Mention some key considerations during installation of a cyclone seperator?

A: Cyclonic separation is a means of separating different liquid phases, or, separating particles from…

Q: write note on pug mill and dough mixer on the Oil & Paint Technology

A: The objective of the question is to understand the role and functionality of pug mill and dough…

Q: Explain Semibatch process?

A: In a batch process, the desired product comes out of the reactor in groups i.e. in discrete amounts…

Q: In the plate and frame filter press, by plotting the filtrate volume as a function of time per…

A:

Q: Explain the advantages of coating process thermal spray coating   a lot of information Do not…

A: Advantages of Thermal Spray Coating 1. Wide range of coating materials  There is a huge range of…

Q: When the instantaneous load is applied perpendicular to the specimen cross section, the material is…

A:

Q: Convert 5.8 Faradays to Coulombs.

A: Definition of Faraday constant The Charge of single mole of electrons is called as Faraday…

Q: Compare the three main types of scrubbers (spray, cyclonic, and venturi) based on their typical…

A: In this question a comparative study of the three main types of scrubbers ( spray,cyclonic and…

Q: Define the Exergy Destruction During Heat Conduction.

A: The destruction of the exergy in the process of heat conduction is to be determined.

Q: Outline the difference between non associate and associated gas

A: Associated gas and non-associated gas both are linked with reservoirs one is produced from crude oil…

Q: How to manufacture ball bearing and what manufacturing processes are involved in manufacturing of…

A: A bearing machine element that enables rotational or linear movement, and reduces friction between…

Q: Bitumen 60/7O Pen is more preferred in hot climate region compared to 30/40 Pen bitumen.

A: Bitumen penetration grade 60/70 means the penetration value is in the range 60 to 70 at standard…

Q: List three types of annealing used in thermal processing of metals, and describe ONE in detail.

A: according to Bartleby's guidelines, I can only solve one question at a time 3) three types of…

Q: How to improve heat transfer by ultrasound: application For a double tube heat exchanger ???

A: A Heat Exchanger is used to utilize the heat of the product stream, in general, to other streams…

Q: could you touch further on the last slide, where does the mixing point come from and also tie lines…

A: Since there are three different components, So simple distillation cannot be done to separate themA…

Q: Given the table below and your judgement for extreme operational conditions, select polymers for the…

A: Given Data Different Material With their Glass Transition Temperature and Melting Point.  To find…

Q: Write about the applications of solar cooling.

A: Solar cooling is a system mechanism that converts heat from the sun into cooling that can be used…

Q: a petroleum crude oil with a specific gravity of 0.865 is flowing through a piping arrangement as…

A: Given: The specific gravity of petroleum crude oil is S = 0.865. Thus, the density would be, ρ = 865…

Q: How is a large surface area achieved for adsorption?

A: The technique by which surface area in large amount is obtained for the adsorption process is to be…

Q: Discuss Lever-Operated Knapsack Sprayer

A:

Q: What are the four elements of corrosion cell ? Give brief description for each of the element.

A: Corrosion cells are a complex case of Electrochemical Phenomenon. The Components and Brief…

Q: Describe the aging (precipitation) hardening by drawing the schematic diagram Explain due to the…

A: Age hardening (also called precipitation hardening) is a heat treatment technique used to increase…

Q: 1.write notes about high density polyethylene and low density polyethylene. 2. Advantages and…

A: Notes on HDPE and LDPE is asked.

Q: Principles of Spherical separator

A: Separators are mainly used to separate liquids with different densities. they form the layers of…

Q: Compare between horizontal and vertical three-phase separator.

A: The three-phase separator is used to separate the well fluids into liquids of two types, oil, and…

Q: For what types of wet solids can fluidized-bed, spoutedbed, and pneumatic-conveyor dryers be used?

A: Drying is the unit operation in which the moisture is removed with the help of drying equipment. The…

Q: Discuss the Water Sachet Failure due to Change in Supplier and one thermal analysis technique for…

A: Introduction Potable sachet water (drinking water)  quality is solemnly dependent on the quality of…

Q: Draw the bonding and antibonding sigma and pi orbitals for n = 2.

A: Our objective is to draw the bonding and antibonding sigma and pi orbitals for n=2.

Q: Suggest two engineering design ideas for better efficiency of a shell of the three phase separators.

A: Hello Subscriber ! You have posted multiple questions. As per our policy, we have answered the first…

Q: what applications does packed column have?

A: Packed columns are commonly used in various industries for separating, purifying, or removing…

Q: Problem and solution for water-in-oil emulsion separator?

A: Problems/Challenges associated with Water-in-Oil (WIO) emulsion separators Separation methods…

Q: Evaluate the performance and behavior of the carbon Steel material used in heat exchanger?

A: Introduction to the problem The goal of a heat exchanger is to transfer as much heat as possible…

Q: High density polyethylene in general is ___ a. high surface area exposed than LDPE b. fluid than…

A: High density polyethylene in general is an given options