3. STATIC EQUILIBRIUM OR NOT: Analyze the different forces applied onthe object in each of the diagram diagram below. Determine what is asked. mass of 6.5 kg is suspendedknot as shown in the figureright. What is the value1, 2, and 3 thatАTiby aon theof tensionssupports the hangingmass. (0 = 40°)T36.5 kg

Since the system is in static equilibrium, hence we can apply force balance equation. Net force in…

Answered: mass of 6.5 kg is suspended knot as…

mass of 6.5 kg is suspended knot as shown in the figure right. What is the value 1, 2, and 3 that А TI by a on the of tensions supports the hanging mass. (0 = 40°) T3 %3D 6.5 kg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The magnitude of the force F is 120 lb. Find its vector representation. 25 ft A 18 ft 15 ft B F y
Learning Goal: To be able to solve three-dimensional equilibrium problems using the equations of equilibrium. Part A As with two-dimensional problems, a free-body diagram is the first step in solving three-dimensional equilibrium problems. For the free-body diagram, it is important to identify the appropriate reaction forces and couple moments that act in three dimensions. At a support, a force arises when translation of the attached member is restricted and a couple moment arises when rotation is prevented.For a rigid body to be in equilibrium when subjected to a force system, both the resultant force and the resultant couple moment acting on the body must be zero. These two conditions are expressed as The J-shaped member shown in the figure(Figure 1) is supported by a cable DE and a single journal bearing with a square shaft at A. Determine the reaction forces Ay and Az at support A required to keep the system in equilibrium. The cylinder has a weight WB = 5.60 lb , and F = 1.50 Ib…
As a follow question to the follow question. Could you explain in detailed how you came about the equation to solve for the reaction at A and B. In a beam like this or any other sort of beam how can I determine how many reactions I have. Also how did you know that the shear force is -250 and bending moment is -250x at section CA could you go more in depth on how you came to that conclusion.
Theory of Structures Calculate all the member forces for the truss given in the figure below, By method of section
Determine the resultant moment produced by the forces about point O.
Question 1: Equilibrium of rigid body The uniform beam AD, which is supported by pin at point A and by roller at point C, carries the loads as shown in the figure below. Neglecting the weight of the beam and considering the system to be at equilibrium, (a) draw the free body diagram of the system (b) determine the reactive force at point C (c) determine the reactive forces at point A. 120 kN/m -2m- 100 KN B 2 m C + 120 kN/m o 2m 30⁰ D 120 kN
RIGID BODY TRANSLATION SHOW FREE BODY DIAGRAMCOMPLETE AND CLEAR SOLUTION DON'T ROUND OFF DETERMINE THE REACTIONS AT B, C, AND D Note: Pin supports can resist both vertical and horizontal forces.
The inverted T-beam supports the concentrated loads shown in Figure. Determine the following: What is the location of the neutral axis relative to the bottom of the beam? What is the moment of inertia of the beam section with respect to the NA? What is the maximum positive moment in the beam (in terms of P)? What is the maximum negative moment in the beam (in terms of P)? What is the maximum allowable value of P in order not to exceed a flexural stress of 4ksi in compression? What is the maximum allowable value of P in order not to exceed a flexural stress of 10ksi in tension? What is the maximum allowable value of P for this beam such that it will not fail by bending?
Calculate the forces in members AB, BG, and GF. Solve for each force from an equilibrium equation which contains that force as the only unknown. Forces are positive if in tension, negative if in compression. 6 kN 2.4 m B 2.4 m C 2.4 m D 2 m AN E 5 m G H :
please show work and free body diagrams so i can learn and understand how you got the answer
a) Find the forces in GR, GC and BC bars.b) Are there any empty bars in the system? explain.
4. Determine the three components of force (F3) the three concurrent forces as shown in the figure. F3=10KN 60° 45 F1=30KN 3 1 14 F2=50KN 60° 30° X