Many chemical processes can be modelled by the following transfer functions K G(s) = Tds e %3D Is + 1 Where K is the gain, J is the time constant and Td is the time delay. Obtain the transfer function for the system in terms of the system parameters. Assume that the time delay Td is a multiple of the sample time T.

Many chemical processes can be modelled by the following transfer functions K G(s) = Tds e %3D Is + 1 Where K is the gain, J is the time constant and Td is the time delay. Obtain the transfer function for the system in terms of the system parameters. Assume that the time delay Td is a multiple of the sample time T.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i need the answer quickly
b) The following figure shows a sampled signal and the desired sampled signal. A digital signal processing system is required to change the sampled signal to produce the desired output signal. 1 Desired output -1 0 1 2 3 4 5 Sampled signal -0.4 -0.3 i) Design the required digital signal processing system and provide the z-transfer function. Determine and comment on the system's stability.
Problem 4: Two lowpass signals each band limited to 3 KHz are to be time multiplexed into a single channel using PAM. Each signal is impulse sampled at frequency of 50% above the Nyquist frequency. The time multiplexed signal wave form is filtered by an ideal LPF before transmission. f1(t) LPF PAM Signal Sampler f2(t) LPF Pulse Clock Gen. a. What is the minimum clock frequency of the system? b. What is the minimum cutoff frequency of the LPF? In the receiver, the signal is impulse sampled and demultiplexed using the system shown, determine the minimum and maximum acceptable BW of the LPF used in retrieving the analog signals.
(a) State the difference between the signal in time domain and frequeney domain. Explain your answer with the help of a sketch for each signal. (b) Sketch and define a sinusoidal signal by labelling its cycle, time duration and magnitude. (c) Sampling frequency is one of the important element in signal processing. Describe the meaning of a sampling frequency using a sketch if possible. Why is it important to set the sumpling rate higher than the maximum frequeney measured? (d) Figure I shows a sinusoidal wave against time in millisecond. If the signal passes through a low-pass filter of cut-off frequeney of 70 Hz, how would the signal look like after the filter? Clearly sketch your answer. iwww 25 50 75 100 125 150 175 200 Time (ms) Figure I
d. flatline 6. Continuous time signal sin (3m) is sampled at a rate of 4 samples per second. At what sample output value reach to peak value (+1V)? Hint. Simulate with sample index n = 0 to 20 samples. a. n=0 b. n 6 C. n 12 d. n= 4
Identify the given statement. FM and PM demodulators can actually reduce noise and increase the signal-to-noise ratio during the demodulation process by using limiters. This is known as the capture effect. Select your answer. The statement has no fixed information. The statement is false. The statement is true. The statement is a case-to-case basis.
ASAP
hand written answer,please
Output voltage, V, of a microphone is a Gaussian random variable with a mean of OV and variance of 2.8V2. Microphone output is processed by a limiting rectifier with cutoff at OV and +4.2V. (Output below OV is clipped to OV, and output above 4.2 V is clipped to 4.2V.) Random variable L is the output of the limiter: a. What is the CDF of L? b. What is the PDF of L? c. What is the E[L]? 0 L = g(V) = {V 4.2 V 4.2
Please check work…
B) The following waveform is the RB (return to bios) representation of the serial digital data, find the digital data code and draw the NRZ (non-return to zero) and RZ (return to zero) waveforms. C) The waveform below is the PAM for the analog signal, draw the analog signal, PWM and the PPM for this signal. 12
a) Find the discrete equivalent to the cinaloa PID contro ller ? Be sampling period I-2. b) Canvert the discrete trons fer function into a Causal discrete difference equation.