manual transmissions are being discussed. technician a says that if it requires gear oil, to always use gl-5 rated oil to protect the synchronizers. technician b says that if it requires engine oil that you should add a friction modifier to it. who is correct?

Q: Question: How can we change the pressure valve of the hydraulic transmission system?

A: A hydraulic power transmission system uses a pressured flow to transport the energy needed to…

Q: Describe the purpose of a viscous clutch.

A: Viscous clutch The clutch is part of the machine that is used to operate for the transmission's…

Q: explain the process for diagnosing a noisy manual transmission while conducting a test drive.…

A: There are a few things that can cause noise in a manual transmission. Some common causes include:…

Q: Technician A says that some small cracks in the accessory drive belt may be within tolerance.…

A: Technician A says that some small crack in the accessory drive belt may be within tolerance limits.…

Q: Technician A says when removing a transmission, the rear of the engine will usually need to be…

A: Answer

Q: echnician A says that RWD transmission valve bodies are serviceable from under the vehicle.…

A:

Q: When discussing the possible causes for a shudder during acceleration, Technician A says that a worn…

A: Shudder is taken place during acceleration at higher speed. The main reason of this problem is…

Q: Question 6 uontanes of the pressure carburetor system.

A: The main advantage of pressure carburettor system are - reducing icing tendency -better efficiency -…

Q: Technician A says that some systems use a special modulated shift control solenoid. Technician B…

A: In automobile the transmission system uses shift control solenoid which shift the gear…

Q: Technician A says that the proper fluid level for a manual transmission is normally to the bottom of…

A: Solution:

Q: 81) Technician A says the quality and feel of a transmission shift depends on the amount of slippage…

A:

Q: Technician A says check balls are often used to block holes between the transmission valve body and…

A: pacer plates are also commonly used in automatic transmissions to provide additional clearance…

Q: Tech A says that negative caster provides directional stability.  Tech B says that positive caster…

A: The caster can be defined as the angle of inclination of the steering axis from the vertical axis of…

Q: Which of the following components is replaced as an assembly?a. The transfer caseb. the viscous…

A: Step 1:The transfer case is often replaced as an assembly due to several reasons :Transfer cases are…

Q: Which characteristic is common to all four-wheel-drive vehicles?   They use a…

A: In four-wheel-drive vehicles, the center differential plays a crucial role in distributing power…

Q: what will happen as the clutch disc wears? a. transmission shifting becomes easier b. clutch pedal…

A: The correct option is: c. clutch pedal free play increases. As the clutch disc wears, the friction…

Q: Pinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is…

A: Given  Pinion gear-to-flywheel ring gear To find Which technician is correct

Q: In a manual transmission what are the seven steps for power flow in  final drive

A: The process of shifting the power generated by the engine toward the wheels is called the…

Q: True or False? A reverse idler gear changes the directionof torque flow to the opposite direction of…

A: Given Data : Reverse idler gear

Q: The functions of a splash shield are being discussed: Technician A says that disc brakes will…

A: The splash shield is a metallic or plastic part that is placed at the bottom portion of the car. The…

Q: Technician A says that the engine oil drain plug typically needs to be replaced with a new one at…

A: At every maintenance trip of the automobile engine oil is changed by removing the oil drain plug.

Q: Which type of drive system can be used designing the camshaft drive of a spark ignition engine? List…

A: given; Which type of drive system can be used designing the camshaft drive of a sparkignition…

Q: 52) Technician A says few production vehicles have transmissions with an internal oil cooler.…

A: Technician A is saying correct statement as the transmissions with the oil cooler are located in the…

Q: List five common sources for transmission fluid leaks

A: five common sources for transmission fluid leaks are following-

Q: Technician A says that all transmission opening pressure are derived from the regulated output flow…

A: Technician A says that all transmission opening pressure are derived from the regulated output flow…

Q: Which of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc.…

A: A vehicle’s sprung weight is supported by springs of one kind of or another (coiled springs, air…

Q: In this diagram, which pressure differential valve has pressure loss? Which part of the system has…

A: Differential valves are used for detecting differential pressure. detection of the valve failure of…

Q: A reddish-colored oil is discovered to be leaking during an engine oil change and inspection:…

A: Leak fluid color and its use in an automobile is shown in tabulated form Leak fluid color  fluid…

Q: What is the importance of aligning the notches found on the cam-gear and crank-gear? (Select the…

A: The aligning of notches plays a very important role in the working of engine.

Q: echnician a says that the malfunction of the ABS can cause the control module to shut off or…

A: Who is correct?

Q: Interaxle differentials are being discussed. Technician A says the interaxle differential is located…

A: It is an separate differential gear box that locks the first and second differential in a tandem…

Q: turbocharging is disengaging the transmission system. increasing the noise coming from the exhaust.…

A:

Q: the number one cause of clutch disc failure

A: Clutch :- The function of a clutch is to transmit the power from rotating shaft or motor or engine…

Q: 109) A customer complains that his vehicle will not move when first shifted into gear. Technician A…

A: When the vehicle sit engine off over night, fluid from the torque converter drains back . It drain…

Q: Technician A says a purpose of a lockup piston clutch is to improve fuel economy. Technician B says…

A: As we know that the purpose of lockup piston clutch is to improve fuel economy as well as it is…

Q: After draining gear oil from a transaxle, the techniciannotices that the oil has shiny, metallic…

A: For a transmission or axle to last longer, it needs to be properly lubricated. After the required…

Q: While discussing transmission adaptive learning: Technician A says that the transmission learns to…

A: Transmission Adaptive learning:-The automatic transmission is designed in such a way that it has a…

Q: What may be caused by improper engine and transmission mounts on FWD vehicles?

A: Improper engine and transmission mount can cause unusual vibrations in FWD vehicles.

Q: 128) Technician A says slide hammer pullers are usually required to remove the front pump from the…

A: A slide hammer puller is a mechanical tool with a long round shaft. It has a hammer weight slides. A…

Q: On an electronically controlled transmission list 5 things that could cause incorrect shift times…

A: In and electronically transmission system is the best transmission system as it gives proper engine…

Q: Tech A says that the weight of the flywheel smoothes out the engine’s power pulses. Tech B says that…

A: Flywheel: A flywheel is a mechanical device having higher value of moment of inertia. This high…

Q: History of manual transmission

A: The first manual gearbox was created by Emile Levassor and Louis-Rene Panhard. The original…

Sensors

Sensors are input devices that provide the output device with the input quantity. They generally detect the variation in the surrounding environment and give output to the relevant system.