MACHINE ELEMENTS 2 A Weight of 112.7 Ib is suspended from a cord wrapped around a solid cylinder of 4 ft radius weighing 483 Ib. the cylinder rotates about a horizontal axle through its mass center. What torque applied to the cylinder will raise the weight with an acceleration of 15fps?. What will be the total bearing reaction? BEARIUG

Q: English: A train carriage consists of a car body and two axles with wheels. The car body has a mass…

A: F = ma so we have to determine the velocity once it has travelled 0.2 m under constant accn.

Q: Because of the way in which the mass is distributed, wheel A has a radius of gyration of 0.65 m and…

A: For each wheels A and BRadius of the wheel A and B is RA= RB=1m Given mass of Wheel A and B…

Q: The figure shows a trolley of mass 10 kg that can move freely along a smooth fixed horizontal rail…

A: Given: The mass of trolley, M = 10 kg The mass of link AB, m = 2 kg The length of AB, L = 1.5 m The…

Q: 40-kg cylinder is hung from the gear system shown. Gear s a mass of 8 kg and a radius of gyration…

A: Given,

Q: A wheel of mass M has radius R. It is positioned vertically on the floor and you exert a horizontal…

A:

Q: The swinging frame of a balancing machine is shown in figure 1. The lever ACB has a mass of 6 kg and…

A: Given:To find:Frequency of vibration

Q: An inelastic cord is anchored at point B at the top of a 20 degree slope as the cord is unwound from…

A: Given: The slope = 20 degrees The mass of the spool, m = 200 kg The inner hub radius, Ri = 0.4 m The…

Q: An object of mass 40 kg has a radius of 0.2 m. If the surface is tilted, there is enough friction…

A: Question is solved below.Please give helpful rating.Explanation:

Q: If the large ring, small ring and each of the spokes weigh 110 lb, 17 lb, and 25 lb, respectively,…

A: Mass of large , small rings and rods are, m1=11032.2=3.416 slugsm2=1732.2=0.528…

Q: The drum shown in Fig. (a) has a radius of gyration of 30 cm and weights 1,8 kN. It is supported by…

A: Given data: k=30 cmw=1.8 kJW=1 kNr=37.5 cm Need to determine the angular acceleration of the drum.

Q: A 4 lb unbalanced wheel is rolling without slipping on a horizontal surface with an angular velocity…

A:

Q: A shaft carries four masses A, B, C and D of magnitude 10 kg, 20 kg, 15 kg and 25 kg respectively…

A:

Q: 1372. The unbalanced wheel shown in Fig. P-1372 weighe 322 Ib and hasa mas radius of Kyration of…

A:

Q: Problem 2: The drum shown weighs 80lb and has a mass moment of inertia about O of 0.8 lb.ft?.…

A:

Q: Bar BC weighs 161 lb and has a radius of gyration of mass with respect to a hor- izontal axis…

A:

Q: A force of P = 20 N is applied to the cable, which causes the 175-kg reel to turn without slipping…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.