Show the given and formula used. M5-8 COMBINED CORRECTIONS. A 50-m steel tape is of standard length under apull of 5.5 kg when supported throughout its entire length. The tape weighs0.05 kg/m has a cross-sectional area of 0.04 sq.cm, and being made ofsteel, its modulus of elasticity is 2.10x106 kg/cm2. This tape was used in thefield to measure a distance that was determined to be 458.650 m. At thetime the measurement was made, the constant pull applied was 8 kg withthe tape supported only at its end points. Determine the correct length ofthe line.

Given data: Length of tape L = 50 m Standard pull P0 = 5.5 kg Weight of the weight w = 0.05 kg/m =…

M5-8 COMBINED CORRECTIONS. A 50-m steel tape is of standard length under a pull of 5.5 kg when supported throughout its entire length. The tape weighs 0.05 kg/m has a cross-sectional area of 0.04 sq.cm, and being made of steel, its modulus of elasticity is 2.10x106 kg/cm². This tape was used in the field to measure a distance that was determined to be 458.650 m. At the time the measurement was made, the constant pull applied was 8 kg with the tape supported only at its end points. Determine the correct length of the line.

M5-8 COMBINED CORRECTIONS. A 50-m steel tape is of standard length under a pull of 5.5 kg when supported throughout its entire length. The tape weighs 0.05 kg/m has a cross-sectional area of 0.04 sq.cm, and being made of steel, its modulus of elasticity is 2.10x106 kg/cm². This tape was used in the field to measure a distance that was determined to be 458.650 m. At the time the measurement was made, the constant pull applied was 8 kg with the tape supported only at its end points. Determine the correct length of the line.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Stepped bar problem solution needed
600 mm 300 mm 300 mm 100 mm * 400 200 mm Figure 2. Determine i, ỹ and z
Question 21 Precision is a term which indicates the degree of conformity of a. repeated measurements of the same quantity to each other b. measured value to its mean value c. measured value to its weighted mean value d. measured value to its true value
Please solve the following with step by step solutions so I can understand.
answers asapppp
Subject: Strength of Materials/Mechanics of Deformable Bodies Solve the following problems as instructed. Boxed final answers and round off to the nearest three decimal places. Show your solutions. Please help me solve, thank you so much!
Determine the centroid of the given figure measured from the given axes. y 2 ft 1 ft 2 ft 3 ft 1 ft
7) What is the length of sides required to cube shown in figure maintain a suspended on water surface if its mass is 100 gram? 2Pag
Please consider te given choices
The deflection of a cantilevered beam where supporting the weight of an advertising sign is given by y = deflection at a given x location (m) W = weight of the sign (N) E = modulus of elasticity (N/m²) I = second moment of area (mª) -Wx? (3L – x) 6EI y = x = distance from the support as shown (m) L = length of the beam (m) Plot the deflection of a beam with a length of 3 m, the modulus of elasticity of E = 200 GPa, and I = 1.2 x 10° mm4 and for a sign weighing 1500 N. What is the slope of the deflection of the beam at the wall (x – 0) and at the end of the beam where it supports the sign (x = L). L Sign Problem 18.5
2:37 20.0 KB/S docs.google.com/forms 55 Write down your year and section. * Your answer Problem 1: The rigid bar AB is attached to two vertical rods as shown. If P=50KN, determine the vertical movement of points A and B. Your answer Figure for Problem 1 ALUMINUM L=4M A=50OMM? E=1OGPA STEEL L=3M A=30OMM? E=20OGPA A 2M 3M B -.
Determine the horizontal component and vertical component of the force that acts at the tip of the boom as shown in the diagram. The force acts perpendicular to the boom, and the boom is raised the given angle relative to the horizontal axis of the truck bed.Report your answer with 3 significant figures and include a (+) or (-) sign before the number to show the direction of the force. Force = 500 lbs; angle = 40 degrees