M5-5 CORRECTION DUE TO TENSION. A 30-m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg, supported for full length. The tape was used in measuring a line 938.55 m long on smooth level ground under a steady pull of 10 kg. Assuming E = 2.0x10“ kg/cm² and the unit weight of steel to be 7.9x10° kg/cm³, determine the following: a) cross-sectional area of the tape. b) correction for increase in tension. c) correct length of the line measured.

M5-5 CORRECTION DUE TO TENSION. A 30-m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg, supported for full length. The tape was used in measuring a line 938.55 m long on smooth level ground under a steady pull of 10 kg. Assuming E = 2.0x10“ kg/cm² and the unit weight of steel to be 7.9x10° kg/cm³, determine the following: a) cross-sectional area of the tape. b) correction for increase in tension. c) correct length of the line measured.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve full SOLUTIONs. One page don't do it in steps thanks
600 mm 300 mm 300 mm 100 mm * 400 200 mm Figure 2. Determine i, ỹ and z
Pls i need answer asap. Show complete solution and figures with unknowns. Fluid Mechanics: A slab of wood 0.80 m x 0.80 m by 0.25 m thick, S = 0.50, floats in water ( specific weight of water=9800 N/m^3 ) with a 840.84 N load on it. Determine the volume of slab submerged in cubic centimeter. Write your answer in whole number.
Question 21 Precision is a term which indicates the degree of conformity of a. repeated measurements of the same quantity to each other b. measured value to its mean value c. measured value to its weighted mean value d. measured value to its true value
Subject: Strength of Materials/Mechanics of Deformable Bodies Solve the following problems as instructed. Boxed final answers and round off to the nearest three decimal places. Show your solutions. Please help me solve, thank you so much!
Determine the centroid of the given figure measured from the given axes. y 2 ft 1 ft 2 ft 3 ft 1 ft
Please consider te given choices
Shown is a 10 by 10 grid, with coordinate axes x and y (Figure 1). The grid runs from -5 to 5 on both axes. Drawn on this grid are four vectors, labeled A through D. This problem will ask you various questions about these vectors. All answers should be in decimal notation, unless otherwise specified. Figure 1 of 1 Part A What is the x component of A? Express your answer to two significant figures. ▸ View Available Hint(s) AI Submit ΜΕ ΑΣΦ 5 -5 D C B A SIXP x axis -5 5 Part B What is the y component of A? Express your answer to the nearest integer. ΜΕ ΑΣΦ Ay = Submit Request Answer ? ?
From the figure below, locate the centroid from x and y axes as shown.
2:37 20.0 KB/S docs.google.com/forms 55 Write down your year and section. * Your answer Problem 1: The rigid bar AB is attached to two vertical rods as shown. If P=50KN, determine the vertical movement of points A and B. Your answer Figure for Problem 1 ALUMINUM L=4M A=50OMM? E=1OGPA STEEL L=3M A=30OMM? E=20OGPA A 2M 3M B -.
Determine the horizontal component and vertical component of the force that acts at the tip of the boom as shown in the diagram. The force acts perpendicular to the boom, and the boom is raised the given angle relative to the horizontal axis of the truck bed.Report your answer with 3 significant figures and include a (+) or (-) sign before the number to show the direction of the force. Force = 500 lbs; angle = 40 degrees
Determine the coordinates of the centroid for the given figure shown.