m.k A brick wall (k =0.9) of thickness 0.18 m separates the warm air in a room from the cold ambient air On a particular winter daw the outside air temperature is -5°C and the room. needs to be maintained at 27°C. The heat transfer coefficient associated with outside air is 20 ().Neglecting the convective resistance of the air inside the room, the heat loss, (2), is

m.k A brick wall (k =0.9) of thickness 0.18 m separates the warm air in a room from the cold ambient air On a particular winter daw the outside air temperature is -5°C and the room. needs to be maintained at 27°C. The heat transfer coefficient associated with outside air is 20 ().Neglecting the convective resistance of the air inside the room, the heat loss, (2), is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
A pipe with 8 cm internal diameter, 9 cm outer diameter, 2 meter long, thermal conductivity 30W/mK is insulated by glass wool material with which thermal conductivity 0,05W/mK, thickness 4 cm. Internal surface temperature of the pipe T1 is 80°C, surrounding temperature where pipe is located is 20°C, convection heat transfer constant on outer surface of insulation is 25W/m?K. Kpo 30W/mk T.= 20°C h. = 25W/MK 4cm K= 0,05W/mK a. Detemine the heat loss from the pipe to surrounding (W)? b. What is temperature of the surface between glass wooden and pipe (T2)? c. What is critical insulation radius for pipe? Is insulation on the pipe succesful? Explain
Q. Steam in a heating system flows through tubes whose outer diameter is 5 cm and whose walls are maintained at a temperature of 130 °C. Circular aluminum alloy 2024-T6 fins k = 186 W/m.K of outer diameter 6 cm and constant thickness 1 mm are attached to the tube. The space between the fins is 3 mm, and thus there are 250 fins per length of the tube. Heat is transferred to the surrounding air at 25 °C, with a heat transfer coefficient of 40W/m².K. Determine: 1. The increase in heat transfer from the tube per meter of its length as result of adding fins. 2. The efficiency of the fins. 3. Temperature at mid-point of the fins. Note: Equations and any other data required can be taken from textbook/handbook. 130°C 25°C
As shown in the sketh below, a steam pipe of 0.12-m inside diameter is insulated with a layer of calcium silicate. "2. Ta2} 1. Ta,1} Steam Insulation (a) If the insulation is 10 mm thick and its inner and outer surfaces are maintained at T, = 800 K and Ta = 490 K. respectively,. what is the rate of heat loss per unit length (q) of the pipe, in W/m? (b) Determine the rate of heat loss per unit length (d), in W/m, and outer surface temperature T,2, in K, for the steam pipe with the Inner surface temperature fixed at T = 800 K, inner radius = 0.06 m, and outer radius n = 0.18 m. The outer surface is exposed to an airflow (T 25°C) that maintains a convection coefficient of h = 25 W/m2-K and to large surroundings for which Tur = T, = 25°C. The surface emissivity of calcium silicate is approximately 0.8.
We have a wall (k = 10 W/mK) with a thickness of 0.4 m. At a certain instance of time temperature distribution is given by T(x) = 50 x²– 450 x + 350. a- Please calculate the rate of heat transfers entering and leaving the wall for a unit surface area and also find the change in the energy storage of the wall. b- If the environment temperature is 85 °C, what is the convection coefficient between the cold surface of the wall and environment.
Question 1 An electric current of 6.4 A passing through a resistor has a measured voltage of 9V across the resistor. The resistor is cylindrical with a diameter of 2.5 cm and length of 15 cm. The resistor has a uniform temperature of 115°C and the room air temperature is 23°C. Assuming that heat transfer by radiation is negligible, determine the heat transfer coefficient by convection.
A plane wall of an oven with an insulation coating is attached to an insulated wall. The thermal conductivity and thickness of the insulation coating are 0.1 W/(m K) and 1 mm, respectively. The material of the plane wall is stainless steel 304. The density, thermal conductivity, and specific heat capacity of the stainless steel 304 are 7900 kg/m³, 74.9 W/(mK), and 477 J/(kg-K), respectively. The wall thickness of the stainless steel 304 is 15 mm. The temperature of the plane wall with the insulated coating is initially maintained at 30 °C. Suddenly, hot gas with a temperature of 1000 °C enters the oven. The convection heat transfer coefficient at the insulation coating surface is 70 W/(m²-K). Insulation Coating Stainless Steel 304 Oven Gas Perfectly Insulated Wall 1 X L 3-1) What is the overall heat transfer coefficient per unit area from the gas to the surface of the stainless steel? The answer should be given in the unit of W/(m²-K). 3-2) What is the value of the Biot number? 3-3)…
When operating at steady-state in a 250C room, the surface temperature of a 20 W incandescent light bulb is 1250C. Approximate the bulb as a 40 mm diameter sphere to estimate the rate of heat transfer from the bulb via convection. Air properties: k-0.030 W/m-K Spear surface area: S=4tr²³ v-20.92x10" m²/s Sphere volume: V=(4/3)Tr Pr-0.700
a. The wall of a building has a surface area of 50 m2. The outside layer of the wall is 20 cm thick concrete with thermal conductivity kcon = .8 W/m-K. The inner layer is 10 cm thick balsa wood (kbalsa = .048 W/m-K) as an insulator. Outside temperatures of 47o C are expected, while an inside temperature of 21o C is maintained by the cooling system. Find the rate of heat transfer through the wall.
A brick wall (k =0.9 ?/ ?.? ) of thickness 0.18 m separates the warm air in a room from the cold ambient air On a particular winter day the outside air temperature is —5°C and the room needs to be maintained at 27°C. The heat transfer coefficient associated with outside air is 20 ( ?/ ?^2? ).Neglecting the convective resistance of the air inside the room, what is the heat loss per unit area?
a. given convective heat transfer coefficient of inside air = 18.23 W/m2K, find the temperature of inside air at the end of composite wall b. neglect natural convection, find heat transfer rate due to thermal radiation c. using heat transfer rate due to thermal radiation, find the innermost wall and interface temperatures
10.The layout of a wall and the heat transfer parameters are shown in the figure below. Find the internal temperature of the wall, T₁. (o= 5.67 x 10-8 W/m²K4 ) (Ans: 569.5K) T1 k=1.1 W/m.K Icond L=0.12m T2=373K x=0.7 grad Iconv Tsur Air Tex = 300K h = = 290K : 18 W/m².K