m³ min A single-acting two-stage compressor delivers air at 16 bar. The volume flow rate of air entering the compressor is 17 with the temperature and pressure of 33° C and 1 bar respectively. If the compressor is designed for minimum work and complete intercooling, determine the power required to drive the first stage if it follows the compression law of PV1.3 = C. (47 kW)

m³ min A single-acting two-stage compressor delivers air at 16 bar. The volume flow rate of air entering the compressor is 17 with the temperature and pressure of 33° C and 1 bar respectively. If the compressor is designed for minimum work and complete intercooling, determine the power required to drive the first stage if it follows the compression law of PV1.3 = C. (47 kW)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single acting two-stage air compressor deals with 4 m^3/min of air under atmospheric conditions of 1.013 bar and 15°C with aspced of 250r.p.m. The delivery pressure is 80 bar. Assuming complete inlercooling, find the minimum power required by the compressor and the bore and stroke of the compressor. Assume a pistonspeed of 3 m/s, mechanical efficiency of 75 percent, and volumetric efficiency of 80 percent per stage. Assumethe polytropic index of compression in both the stages to be it = 1.25 and neglect clearance.
4. A single-stage cylinder air compressor is rated at 6.5 cubic meter per minute of air .Suction conditions are 1 atm and 27 deg C and discharge pressure of 1034 KPa. The compression process follows PV1.35 = C. What is the engine Kw power needed to drive the unit if the combined engine-compressor efficiency is 84%?
Q17
The compression ratio of an Otto cycle is 8, at the beginning of the zanthropic compression process, the pressure of the air is 100 kPa, the temperature is 27 "C, the volume is 550 cm. At the end of the lzantropic expansion process, the temperature of the air is 700 K. Using the specific temperature values at room temperature (according to the cold air standard assumptions) Find the gravity of the air.
Q17
. Steam enters the turbine at 10 bar. Output pressure P = 1 bar, knowing turbine efficiency is 80%. Find the state of the fluid leaving the turbine (If liquid or vapor, find temperature; If liquid-vapour mixture, find q). Calculate the work done per kg of steam entering:a. The inlet steam temperature is 250oC .b. The inlet steam temperature is 325oC
A four-stage compressor works between limits of 1 bar and 120 bar. The indexof compression in each stage is 1.25, the temperature at the start ofcompression in each stage is 30 ˚C, and the intermediate pressure areselected such that work is divided equally among the stages. If the clearanceis negligible: Calculate:1 the intermediate pressure in each stage2 the temperatures at the end of each stage3 the mass flow rate in kg/h if work input is a unit kW
3. A single stage air compressor hadles 0.454 m^3/sec of atmospheric pressure, 27 deg. C air, and delivers it to a receiver at 652.75kPa. Compression is isothermal. Determine the work in kW
A single stage double acting air compressor of 150KW power takes air in at 16 bar & delivers at 6 bar. The compression follows the law PV1.35 = C. the compressor runs at 160rpm with average piston speed of 150 m/min. Determine the size of the cylinder.
Q2. An idea Otto cycle has a compression ratio of 11, takes in air at 100 kPa and 25 °C. The rotational speed of the cycle is 2000 rpm. Using constant specific heats at room temperature, sketch P-V diagram of the cycle and determine the thermal efficiency and the rate of heat input if the cycle produces 180 kW of power
The answer was given all i want is the correct solution thank u
2. An air compressor is to compress 510m²/hr from 100kpa to 10bar, for an ideal compression with n=1.3, what will be the percent saving in power due to two staging?