locst 3) ZOH (11) (ST2) For the ZCH setermine +he Ndarmain with sampled yorem transfer function. GzAs (E) (if T=l sec).

Q: Q1/Determine the transfer function C/R for the system below using Signal Flow Graph technique. E[s]…

A:

Q: For the opam output given below , Vmax=4.6V and Vmin =-4.6V Find the slew rate SR of op-amp . Vo…

A:

Q: Convert each block diagrams into a signal flow graph and solve for the equivalent transfer function…

A: Q1)Step 1:Step 2:Step 3: Q2)Step 4:

Q: For the opam output given below , Vmax=8.9V and Vmin =-8.9V Find the slew rate SR of op-amp . Vo…

A:

Q: Q2) For the mechanical system in figure (1). Drive the transfer function Y(s)/F(s) KI

A: Find the transfer function of the mechanical system.  Transfer function is ratio of the Laplace of…

Q: Given a signal varying between (+/-) 5.0 V, what is the minimum step change if a 12 bit DAC is used?…

A: Step size = reference voltage /(2n-1) Where n is the no. Of bits of DAC . Given DAC is 12 bit .

Q: 4- Nontouching-loop gain taken three at a time. (B): It is required to use Mason formula to find the…

A:

Q: (a) What are the functions of capacitors C1, C2, and C3 as shown? (b) What is the magnitude of the…

A: a) Here, AC current have low impedance path in capacitor C1 Capacitor C1 behaves as a bypass…

Q: 2) Find the reduce transfer function of the following.

A: This is a basic problem of block diagram reduction The solution is given below

Q: Consider the following circuit, if R1 = 1 kOhm and R2 = 5 kOhm, and Vin = 12V. The output Vout of…

A:

Q: 7

A:

Q: NH plns ain1na7 Engineering and Numerical Analysis HiwiDerter mime Lablace Tronsform of tho puls…

A:

Q: H2 R + G1 G2 G3 H1

A:

Q: Find the Transfer Function of the block diagram drawn in Figure 3 using Block Diagram Reduction…

A: The transfer function can be obtained by reducing the series and parallel connected block reduction…

Q: he close loop system block diagram is given below .Find the transfer function of the given system.

A: The transfer function is the laplace transform of the ratio of the output to the input of the system…

Q: (f) For the block diagram of a control system shown in Figure Q1b, derive the closed-loop transfer…

A:

Q: Assume that m(t)=10 cos 500t and c(t) = cos 5000t . In DSB-SC, the modulation and demodulation…

A:

Q: Ta o lo RL IQ is 50 uA, RL is 2kOhm. What is Vo when the differential inputs are such that the…

A: IQ1 =24.9uA IQ2 = IQ-IQ1 IQ2 = 50 -24.9 = 25.1uA

Q: Ris O- Reduce the signal flow graphs into a single transfer function Fill in the blanks the…

A:

Q: . Consider the system below. Determine (a) State-Space Model, (b) Transfer Function. R1 = 50 R2 = 30…

A:

Q: с. Determine y[n] = x[n] method. Sketch the obtained output of y[n]. h[n] by performing analytical

A: When a dynamic system is faced with a brief input signal, termed an impulse, the impulse response,…

Q: X1 021 413 032 2x X3 033 023 012 043 'x Q

A: Given data The above signal flow graph contains two closed loops and multiple forward paths. As…

Q: Ing equations. Obtain overall transfer function using Mason's gain formula X2 = d12X1+ a32*3 + a42X4…

A:

Q: 8. Write the mason's gain formula for signal flow graph and define each term. P = G(s) = E,P& Ak /

A:

Q: please give me the accurate ans with 40 minutes , tq

A: Detailed explanation:

Q: Question fcx)- gcx2 foo * PAX) * fa) PC) = RCX,) * BCX, )

A: Signal-processing systems can be categorized in the same way as signals are. That is,…

Q: The signal flow graph of a complex system is shown in Figure 2.a. Determine the overall transfer…

A:

Q: R ell e a. What the transfer function of this ? b. Please draw the block diagram of this ?

A:

Q: III-Find the Q point of JFET circuit. Graphical Analysis of a Self-Biased JFET You can use the…

A: The Q point is defined as Vds(drain to source voltage) and Id(drain current). We have to apply KVL…

Q: Construct a signal flow graph from the following equations. Obtain overall transfer function using…

A:

Q: Per harmonic up to th 4m harmonc for the perio cic signal shown below. -ion gene ral the avurage wer…

A: The given periodic signal is shown below:

Q: Section B: 1. Design a 5-bit divider to divide the 6-bit by two using a shifter circuit.

A:

Q: 3. E(S) 1(8) Cas Cis Cis R;C3s + 1 C38 R

A: The signal flow graph will be as :-

Q: Q4: A Low pass filter (current mode conversion) is shown below: R: io Using a current source I, an R…

A: The solution is given below

Q: I. From the next model, obtain: a. The transfer function representation G(s) = V,(s)/V¿(s). b. The…

A: First, we are going to apply Laplace transform in the below circuit.

Q: 5. Consider the non-inverting Schmitt trigger we discussed in class. If R₁=2 KQ, R₂=3x2=6 KQ, V₁=…

A:

Q: Reduce the control system block diagram shown in Figure Q to a single transfer function…

A:

Q: Draw a block diagram with minimum 3 sub system. Simplify it to find the transfer function. Also draw…

A: Transfer Function: It is defined as the ratio of Laplace transform of output to Laplace transform of…

Q: Construct a signal graph from the following equations. Obtain overall transfer function using…

A:

Q: For the opam output given below , Vmax=7.6V and Vmin =-7.6V Find the slew rate SR of op-amp . Vo…

A:

Q: c) Explain the effect of these actions on a filt er output: i. Increasing the number of n elements.…

A: