Load 2: A motor draws 22 kW at 0.8 pf lagging. hree loads are connected in parallel across a voltage source of 208 V rms: Load 1: An impedance of 15 + j8 . Load 3: A capacitive load rated at 16 kVA at 0.85, Determine the total complex power, the power factor of the combined load, and the necessary capacitance to correct the power factor of the combined load to unity pf.

Load 2: A motor draws 22 kW at 0.8 pf lagging. hree loads are connected in parallel across a voltage source of 208 V rms: Load 1: An impedance of 15 + j8 . Load 3: A capacitive load rated at 16 kVA at 0.85, Determine the total complex power, the power factor of the combined load, and the necessary capacitance to correct the power factor of the combined load to unity pf.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

When a load is connected to a power line with a frequency of 230V (rms) 50 Hz, it draws 4500 W at a power factor of 0.80. Find the required capacitance value to increase the power factor to 0.85.
In the picture below the tension line RMS value is 208 V. Determine the average power in the load
Three loads are connected in parallel to a 240-V, 60 Hz supply. Load 1 is composed of three 600-W heaters, Load 2 is a 3 HP, inductive motor with an efficiency of 90% and a p.f. of 0.88, while Load 3 has an impedance of 12-j16 ohms. Determine the following: a) The apparent power of each load b) The Total Power, Total Reactive Power, Total Apparent Power, Power Factor c) The source current
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following: e. Reactive power supplied by the sourcef. Apparent power of the circuitg. Power factor of the entire circuit
If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b. -12000 + j16000 VA Oc. 12000 + j16000 VA O d. None of these
RMS Value of sinusoidal current is given by O a. Im//2 b. I,x2 Ос. c. ImX/2 O d. I/2 m
Two loads are connected in parallel to a 1000 v(rms) 60Hz source. One of the loads has an average power of 500 kW and a forward power factor of 0.9. Since the other load absorbs 400kw and 600kvar power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) Find the value of the capacitor to be connected parallel to the loads so that the power factor is 0.95 back d) Find and compare the magnitude of the current drawn from the .source for the situations before and after the capacitor is connected not: Please solve this question in detail, in a way that I can understand
Sine wave A has a positive-going zero crossing at 40°. Sine wave B has a positive-going zero crossing at 45°. Determine the phase angle between the two signals. What signal leads ? A Y-connected system can have wires. The (resultant) voltage between the hot legs (135V) is The phase angle between the phase voltage and the line voltage of a A-connected generator is degrees. The phase current produced by a certain 20V, Y-connected generator is 12A. The corresponding line current is A certain A-connected generator produces phase voltages of 30V. The magnitude of the line voltages are When the turns ratio of a transformer is 20 and the primary ac voltage is 6V, the secondary voltage is If 20W of power are applied to the primary of an ideal transformer with a turns ratio of 8, the power delivered to the secondary load is The turns required to match a 500 source to a 1000 load is
A load is supplied by a 230 V, 50 Hz source. The active power P and the reactive power Q consumed by the load are such that 1 kW SPS2 kW and 1 KVAR SQS2 KVAR. A capacitor connected across the load for power factor correction generates 1 KVAR reactive power. The worst case power factor after power factor connection is Options: 1. 0.447 lag 2. 0.707 lag 3. 0.894 lag 4.1
For a source which has load has the following characteristics: • Vrms = 125 20° V • P= 400 W • pf = 0.925 lagging What is the rms current and reactive power?
Two 660 V (rms) loads are connected in parallel. The two loads draw a total average power of 76.2 kW at a power factor of 0.8 leading. One of the loads draws 46 kVA at a power factor of 0.96 lagging