LO5 Below is an LC filter circuit, which "smooths" the input source, which is a triangular signal with period T, into an output signal that is sinusoidal, with same period. Assume the peak voltage of v, (1) is 15 V and of v, (t) is 10 V. a) Compute the RMS voltages for v, (t) and v, (1). b) Compute the total power dissipated by the two resistors. (1) 52 v,() 152 LC Filter

LO5 Below is an LC filter circuit, which "smooths" the input source, which is a triangular signal with period T, into an output signal that is sinusoidal, with same period. Assume the peak voltage of v, (1) is 15 V and of v, (t) is 10 V. a) Compute the RMS voltages for v, (t) and v, (1). b) Compute the total power dissipated by the two resistors. (1) 52 v,() 152 LC Filter

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the input signal, which one is the output wave-form for the given circuit? Vmax Vin V in Vout RL Vma INPUT WAVEFORM Lütfen birini seçin: a. Vout -(Vmax-V) Time t Vout time -(Vmax+V Vout Vmax-V Time t Vmax O d. Vout Time t Vmax e. Volt Vmax Timet
For the signal and circuit below, determine the maximum frequency that may be used. Op-amp slew rate is SR = 0.9 V/us. Refer to the image for the circuit, but refer to the following for the given values: Rf = 323996 ohms, Ri = 14089 ohms, Vi = 0.03 C, and w = 404604 x 10^3 rad/s. Express your answer in 10^6 rad/s, no units required, round-off up to two decimal places.
The buck regulator in the next figure has an input voltage Vs = 15 V. The required average output voltage Va = 6.5 V at la = 0.5 A and the peak-to-peak output ripple voltage is 10 mV. The switching frequency is 20 kHz. The peak-to-peak ripple current of inductor is limited to 0.25 A. Determine (a) the duty cycle k, (b) the filter inductance L, O the filter capacitor C, and (d) the critical values of L and C. Q1 +eL iL + + ile io,la 10 Control Dm C Vc vo. V Load
(please solve by hand)
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (lo in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1, and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. The quality factor (Q1) for curve 1 is about: 7.5 5- 2.5 1-10 1-10 1-10 1-10 Frequency (f), Hz O a. 20000 Hz O b. 0.5 O c. 0.23 O d. 2 O e. 1.5
а 5-657 0 1 2 3 4 5 6 7 5.657 Real part of (x(n)) -5.657 Zmaginary part of 2 (m) 0 1 2 3 4 5 6 7
AC Circuits An RC high-pass filter is shown in the figure. Its purpose is to attenuate lower frequencies while allowing higher frequencies to pass through. A 1020-Hz sine-wave signal with rms amplitude of Vrms = 2.5 V is fed into the filter. The values of the components are R = 140 Ω and C = 0.76 μF. Part (a) Find the output rms voltage, in volts.
If vsig is a triangle waveform, determine the maximum amplitude that vsig can have? Showyour calculation.
2. (b) A periodic composite signal is composed of 2 sine waves(S1,S2). The frequency (f) and maximum amplitude (A) of each sign wave is given below: S1:f = 5KHZ , A = 6V S2 :f = 8Khz , A = 4V Draw a frequency domain graph to represent this information. What is the bandwidth?
QI-A) A sinusoidal vohage v,(t) = 20 sin wtis passed through half waverectifier. Find 1) The period T. 2) The DC value of output voltage o- 3) The first harmonics of output voltage in.
I need the answer quickly
Given: Vin = Vpeak sin(w)(t) Vpeak = 5V R1 = 1k ohms Using ideal forward voltage of 0.7V What is the Vo and Vin waveform for 2 periods on the same axis. Label the zero crossings (in radians) and peak voltage of Vo. Calculate for the average Vo and derive a formula for Vo in terms of Vpeak .