Lluid mechanesypeetNewtenA flal plate havingLLleddimension1227e2m x2slideshach.m mclined plane at andewn2lad tothe hoizonalgle ofal aspeed of lm/secThethe1lned plane is lubtinaled byLon film ot01l bavingaVISOLitaot30m-pa.The plate has a umflomLhickneis ef20mmansa density ot40000km)m3Delesminethethiknosof tilm.

Given:Area,A=2*2 =4m2θ=1 rad =57.3°v=6 m/sμ=30*10-3 Pa-sthickness of plate,t=20 mmdensity of…

Lluid mechahus. flat plate having e A Imension 2m x2m slides inclined Plane at an an 2lad to the heizental mgla ef al a speed of 0/sec The inclined plane is lub Xicated by A Lhin film of 01l baving a a visoLity ot 30m-pa.S The plate has a umfolm thickness of 2omm and a density ot 4o000km)m? Delesmine. Ehe tmiknoss Lhe lub riating

Lluid mechahus. flat plate having e A Imension 2m x2m slides inclined Plane at an an 2lad to the heizental mgla ef al a speed of 0/sec The inclined plane is lub Xicated by A Lhin film of 01l baving a a visoLity ot 30m-pa.S The plate has a umfolm thickness of 2omm and a density ot 4o000km)m? Delesmine. Ehe tmiknoss Lhe lub riating

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

f jon The pilot of a crippled jet was able to control his plane by throttling the two engines. The plane has a weight of 17000 lb and a radius of gyration of kg = 4.7ft about the mass center G. Originally the plane is flying straight at a speed of 1200 ft/s. Neglect the effects of 5000 lb as shown, determine: drag and the loss of fuel. If the thrust in each engine is altered to T₁ = 800 lb and T₂ Remark: The counterclockwise sense is the positive sense. 1.25 ft T₂ 1.25 ft T₁ 1:21:02 7
A flat plat 1200 cm x 280 cm is kept in a fluid which has a velocity of 570 m/s.lIf resultant force acing on the plate is 280 kN then calculate 3 the lift force. Assume the density of the fluid is 2.3 kg/m³ and the viscosity of the fluid is 0.21Poise. pkg/m³ vm/s Lift Drag
Please fast
rerce D6 =blank Dimetr Yedaction Fn =0015 Y(Pi-CDp Ev-vam velocity PP- Panch Diametr FELt Ye Sreching force woling force drawing foreo 2. 25 ower Kx=0.98+o.02 Rd=die corner vadus mui die shape facArin extrustion -Lentn tthicknes YA=Stess ) Dirct on 1 The data given in Table Q1(a) corresponds to a cold heading operation performed to make square head on a steel bolt. Figure Q1(a) shows the dimensions of the bolt to be produced. Strength coefficient for the steel Table Q1(a) Strain hardening exponent 550 MPa Coefficient of friction at the die-work interface- 0.21 Thickness of wire stock out of which the bolt is made 0.16 Final length of the bolt. 10 mm 120 mm Compute: (i) The length of stock must project out of the die in order to provide sufficient volume of material for this upsetting operation. (ii) The total number of bolts that can be made out of 6 m rod (wire stock) (iii) The maximum force that the punch must apply to form the head 5 mm 10 mm 15 mm Figure Q1(a)
Fuild mechanics
Please show your step by step solution thank you
Please correct answer
- An arrow is layinched at va so m/s and 10°. Fird the maximun. height, and the fime it takes to reach this height Answer: h 134.78 m, t=5.24 jec. %3D Provide compele soition witn derivarion ot fonnulas (integrals and denvatives). Complete unit / soution piease. Gravitational constant g=9-8
Compite the IMAf of the engine lift shown in The second diagram
10 m 100 APag Low side fil fludd density 1100 ke/m3 910 kg/m3 Level range 2-10 meters ir you are collbrating the transmitter what is the pressure to be applied to the low side at the URV? The gravity is 9.81 mus2. Select one: O 107.91 kPag Ob. 1864 kPag Oe 10791 kPag Od 18.64 kPag
Q1
Please solve asap