need both parts show every single step ....part a answer is correct and part b is incorrect Liquid water enters a cooling tower operating at steady state at 39°C with a mass flow rate of 105 kg/h. Cooled water at 25°C exitsthe cooling tower at the same mass flow rate. Makeup water is supplied at 23°C. Atmospheric air enters the tower at 30°C, 1 bar,35% relative humidity. A saturated moist air stream exits at 34°C, 1 bar.Determine:(a) the mass flow rates of the dry air and makeup water, each in kg/h.(b) the rate of exergy destruction within the cooling tower, in kW, for To 23°C.Part AYour answer is correct.Determine the mass flow rates of the dry air and makeup water, each in kg/h.ma =86900kg/hrmmw =2217.68kg/hrBoth need partParti* Your answer is incorrect.Determine the rate of exergy destruction within the cooling tower, in kW, for To = 23°C.Éa = i20.31kW

Answered: Image /qna-images/answer/83ecec3d-08c0-4d85-902d-95e67646ed0d.jpg

Liquid water enters a cooling tower operating at steady state at 39°C with a mass flow rate of 105 kg/h. Cooled water at 25°C exits the cooling tower at the same mass flow rate. Makeup water is supplied at 23°C. Atmospheric air enters the tower at 30°C, 1 bar, 35% relative humidity. A saturated moist air stream exits at 34°C, 1 bar.

Liquid water enters a cooling tower operating at steady state at 39°C with a mass flow rate of 105 kg/h. Cooled water at 25°C exits the cooling tower at the same mass flow rate. Makeup water is supplied at 23°C. Atmospheric air enters the tower at 30°C, 1 bar, 35% relative humidity. A saturated moist air stream exits at 34°C, 1 bar.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

q12 Complete the answer
What’s the correct answer for this please?
You are given a metal rod, cut to a length of 12 in plus/minus .25in. Then you need to cut off 2 in with an accuracy of plus/minus .25 tolerance. You end up with a 10 in rod but what is the tolerance? (hint: rely on the basic principle of tolerance
Dimensions and magnitude mean size, for example the diameter of the wheels of a mountain bike etc. Select one: True False
Answer the questions below, (Insert the numerical value only, do not use ,+, *, or /) The Relative error for your answer should be less than 0.01, which means if the answer was 50, then the error should not exceed 50*0.01= ±0.5! if the answer was 230, then the error should not exceed 230*0.01= +2 3! if the answer was 2.31467*10^ 3, then you should enter this value: 0.00231467, not this 0.0023 !!!! K2 K1 M1 fv1 M2 f(t) if M1=4, M2=3, fv1=7, K1=4, K2=6. Find the state equations for the translational mechanical system shown in Figure. [d/dt(r1) d/dt(v1) [(1.1) (1.2) (1.3) (1.4) rl (1)] (2.1) (2.2) (2.3) (2.4) (3.1) (3.2) (3.3) (3.4) [(4.1) (4.2) (4.3) (4.4)] vl * f(t)$$ $$ d/dt(r2) d/dt(v2) r2
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
Find a and b so that the ordered data set has a mean of 24 and a median of 38.15, 32, 25, 28, 37, a, 45, 64, 75, b
When no geometric tolerance is specified, the size tolerance controls the well as the size. O form orientation O profile O position as
Q/Answer the following blanks 1. The chemical formula of the maximum copper ore is ...: 2. The chemical formula of the minimum copper ore is .: 3. The copper ore which contain a percentage ratio of iron is .: 4. The pure copper is and ductile and soft with color of .. 5. double fluoride of aluminium and sodium called as 6. the copper-zinc alloys are named as. ***........ 7. The softest and heaviest of all the common metals is. . 8. The zinc ore which is included percentage ratio of Sulphur is 9. Shape, color, and size are properties. 10. The nonferrous metal which is high density and easy workability is ............ 11. In Rockwell test, the major load is applied for a specified time . .beyond zero 12. The of the indent .is a function of the test force divided by the curved surface area 13. The charge is fed through a charging door and is heated to . radiation of heat in open hearth. .mainly by 14. the metals flow and a relatively large permanent set takes place without a noticeable…
Calculate the Minimum Y distance on the drawing below: 1.000 O 2.000 O .460 O .510 1.966 O .500 C 2.000 Ø.995-1.000 6.00 0.008 MABC 3.000 Y 01.005-1.030 +0.005MABC B A .XX = .01 ANGLES= ± 1°
Can you please show how you got the quadratic interpolation please
Choose the correct answer below and show your solution completely. Make sure that your finals answer is 4 decimal places.