Liquid mercury at 0.5 kg/s is to be heated from 300K to 400K by passing it through a 50mm diameter tube whose surface is maintained at 450K. Calculate the required tube length by using an appropriate liquid metal convection heat transfer correlation. Compare your result with that which would have been obtained by using a correlation approximate for Pr > 0.7.

Liquid mercury at 0.5 kg/s is to be heated from 300K to 400K by passing it through a 50mm diameter tube whose surface is maintained at 450K. Calculate the required tube length by using an appropriate liquid metal convection heat transfer correlation. Compare your result with that which would have been obtained by using a correlation approximate for Pr > 0.7.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A horizontal pipe of 100-mm-diamter and 1 m long with a surface temperature of 94 ℃ is used to condense saturated steam at 1 atm. Determine the heat transfer rate for the condensation process. Properties of Water, vapor (1 atm): Tsat = 100℃, ρv = 0.596 kg/m3, hfg = 2257 kJ/kg;Water, liquid (Tf = 370K): ρl = 960.6 kg/m3, Cpl = 4214 J/kg.K, μl = 289*10^-6 N.s/m2, kl = 0.679 W/m.K. Select one: a. 28567 W b. 18254 W c. 19076 W d. 22552 W
A- Cylinder has a 0.1m in length and 0.1min diameter, is initially at 292 K. It is suspended in a steam environment where water vapor at 373 K condenses on all surfaces with an effective film coefficient, h, of 8500W/m2 K. Determine the time required for the center of this stubby cylinder to reach 310 K. If the cylinder were sufficiently long so that it could be considered infinite, how long would it take? (4 Marks)
Air is to be heated by passing it across the tubes of an in-line tube bundle consisting of 8 rows of 25 mm OD tubes in the direction of flow and 10 tubes in each row normal to the flow. Air approaches the tube bank in the normal direction at 30 °C and 1 atm with a mean velocity of 10 m/s. The tube spacing is 37.5 mm in both parallel and normal to the flow. Calculate the heat transfer from the bundle per m of length when the tube surface temperature is 90 °C.
Saturated steam at 1 atm is condensed on the external surface of a copper tube withan outside diameter 16 mm and tube wall of thickness 0.5 mm. The tube is cooledinternally by water with a mass flow rate of 0.06 kg/s, which in turn is raised intemperature from 15 oC to 60 oC as it flows through the tube.Take the heat-transfer coefficient at the condensing side as 10.0 kW/m2K and theisobaric specific heat-capacity of water as 4180 J/kg K.i) Calculate the heat transfer rate to the cooling water. ii)
A vertical tube of 1m length is exposed to atmospheric steam. The mass of steam condensedper hour is 125 kg/h , calculate tube diameter ?( the wall temperature is 70 oC
You are designing a pin-style heatsink for forced cooling of an IC. A small fan blows RT air into the heatsink at about 2.3 ? ? . The aluminum pins are 2mm in diameter and have a constant surface temperature of 120°?. The heatsink is 100mm x 100mm and the pins have an inline arrangement with a transverse pitch of 4mm and a longitudinal pitch of 6mm. What is the total heat dissipation of this heatsink? The pins are 30mm high. Note RT=25 celsius
Proflem # 27. iA fillud with water to a level and is éxposed, to dng air at 30°C. 40 mm deep a pan of of 20 mm mass diffusivity fove for time' reguired evapor ate. -3 m² /. for all the water to 2.5x 10
Q) Compare the heat transfer coefficients under the following conditions (Assume flow is turbulent). (1) Two fold increase in the diameter of the tube; the flow velocity is maintained constant by a change in the rate of liquid flow. (2) Two fold increase in the flow velocity by varying the mass flow rate. Comment on. the results.
Must solve all questions.
2-D: A fin may be manufactured as an integral part of a surface by using a casting or extrusion process, or it may be separately brazed or adhered to the surface. From thermal considerations, which option is preferred? 2-E: What is the difference between steady-state and transient heat transfer processes? Give an example for each of them. 2-F: What is the physical interpretation of the Biot number? 2-G: For flow over a flat plate, sketch variation of local convective heat transfer coefficient, h(x), versus the distance along the plate x for laminar, transition, and turbulent flow regimes.
A copper rod of 30 kg initially at the temperature of 300 °C needs to be immersed and fitted tightly into a ABA alloy ring with inner diameter 30.0015 mm found in tank of 100 liters water of 25 °C. (i) Determine the diameter copper when it is 300 °C. (ii) In your opinion, does the copper rod will still fit tightly into the ABA alloy ring inner diameter 30.0015 in the ambient air condition of 25 °C. Provide your answer in 4 decimal places. Assume the alloy ABA is very small with negligible effect in heat transfer. [Density for copper = 8890 kg/m3, Specific heat, Ccopper = 385 J/kg.°C;Coefficient of thermal expansion, αCopper = 18.0 × 10-6 (°C)-1]. [Density for ABA alloy = 8500 kg/m3, Specific heat, CABA = 138 J/kg.°C;Coefficient of thermal expansion, αABA = 13.3 × 10-6 (°C)-1]. [Density for water = 1000 kg/m3, Specific heat, Cwater = 4200 J/kg.°C].