liquid having a density of 801 kg/m3 and a viscosity of 1.49x10-3 Pa.s is flowing through a horizontal straight pipe at a velocity of 4.57 m/s. The commercial steel pipe is 1.5-in nominal pipe size, schedule 40. For a length of pipe of 61m, do as follows a. Calculate the friction loss Ff.  b. For a smooth tube of the same inside diameter, calculate the friction loss. What is the percent reduction of Ff for the smooth tube

Q: Question? H.W : Find the Reynolds number and estimate the type of flow, when used the water with…

A:

Q: Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40…

A:

Q: A horizontal pipe with a diameter of 350 mm discharges water at the rate of 12 m2/ min and has a…

A:

Q: Water at 25 ° C circulates through a steel pipe. The nominal diameter of Schedule 40 pipe is 2…

A:

Q: H.W: estimate the diameter for a commercial steel pipe with the following characteristics: Length =…

A:

Q: ( Use nomograph AND the formula) Size a pipe that will not exceed 48' of HL in 6000 feet of pipe at…

A: Given data: Head loss, HL = head loss due to friction, Hf= 48 ft Length of the pipe, L = 6000 ft…

Q: Acetone at 77degrees flows around the tubes and inside the rectangular passage shown in the figure…

A:

Q: Calculate the pressure drop across a fully open angle valve placed in 5-in Scheduled 40 steel pipe…

A: To find: The pressure drop across a fully open angle valve. Given: The rate of heat transfer Q=847…

Q: -5 lb-s A fluid with specific weight 73 and viscosity 4.7 x 10 two tanks below through a 3-in pipe.…

A: Given:Specific weight of fluid, γ=73 lb/ft3Viscosity of fluid, μ=4.7*10-5Pipe diameter, d=3…

Q: Calculate the maximum volume flow rate of fuel oil at 45°C at which the flow will remain laminar in…

A:

Q: A pilot tube was used to measure the velocity of water in a circular pipe 2 inches diameter. If the…

A: A Pitot tube is used to measure the local velocity of flow. it is highly accurate velocity measuring…

Q: 8. Oil with specific gravity of 0.80 flows through a pipe X 200 L/s at elev 20, 200 mm diameter, 200…

A: Solution: Given Data: *The specific gravity of the oil is, SG=0.8 *The flow rate through the pipe…

Q: Question 1 Calculate the frictional head loss of a cast iron pipe, L=100m, v=2m/s, D=2", E= 0.15,…

A:

Q: Read the question carefully and give me right solution with clear calculations.  Note: pipe size…

A:

Q: The velocity of water flowing in an 80 mm diameter smooth pipeof length 0.2 km is 3.2 m/s. Calculate…

A: Givenwaterd=80mmL=0.2kmV=3.2 m/s

Q: Problem 1: For the system shown in the diagram below, let 4z = 80 m and L = 185 m of cast iron pipe…

A: To determine:Pipe diameter(D)

Q: 3 whot is the pressure in a 9.7-in bore horizontal pipe, :f the bore of the pipe norrows to 4.1 in…

A: Fluid Pressure Fluid Pressure is the pressure at point in the fluid arising due to weight of fluid.…

Q: To compute the friction factors, you are assuming that the only losses in the system are due to…

A: Whenever fluid flow through the pipes there is always some kind of head loss is happened due to the…

Q: Water @ 4C flows through a 100-mm ID smooth pipe. The Reynolds # of the flow is 150000. Determine…

A: To Find : The maximum velocity. Given : The diameter is d=100 mm. The Reynolds number flow is…

Q: Fuel oil is flowing in a 4-in Sch maximum rate for which the flow is laminar. If the oil has a…

A: The head loss in the pipe can be calculated using the formula given below as- hf=32μuLρgd2 where, u…

Q: What is the minimum pipe diameter in cm that can be recommended if the flow is 5 m^3/s and the…

A:

Q: Determine the total length of a wrought iron pipe (e = 0.000046) with a diameter of 1.5 in which…

A:

Q: 8.20 For a turbulent flow of a fluid in 0.6 m diameter pipe, the velocity 0.15 m from the wall is…

A:

Q: Fuel oil (sg=0.94) is being delivered to a furnance at a rate of 60 gal/min through a 1 1/2in…

A:

Q: Water at 60F is flowing through a 3-inch inside diameter smooth horizontal pipe. If the Reynolds…

A:

Q: Current Attempt in Progress The kinematic viscosity and specific gravity of a liquid are 3.7 x 10-4…

A: Only one question is allowed to solve.

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: The power required by the pump can be calculated using the formula given below- P=ρgQhm where, g is…

Q: What diameter is required in a pipe with t=0.2 mm and a length of 2450 m, yes it is desired that…

A: To find : The required diameter in a pipe. Given : The thickness is t=0.2 mm. The discharge is…

Q: What is the Reynold’s number for a flow of oil (SG = 0.80, ? = 0.00200 lb-s/ft2) in a 6-in diameter…

A: To find: The Reynold’s number for a flow of oil and also check whether the flow is laminar or…

Q: 1.Shear stress velocity, u * has the link with mean flow velocity, u in a pipe for Re > 2300 .…

A: Given: The mean velocity is u= 2 m/s, The Reynold's number is Re > 2300, The friction factor is…

Q: What level h must be maintained in Fig. to deliver afl ow rate of 0.015 ft3/s through the 1/2-in…

A: Given data: For Water at temperature 20 degrees Celcius                      Flow rate = 0.015 ft3/s…

Q: Show complete solution. Units must be included in all calculations. All numerical values should be…

A: