li f at aor

Q: Convert the binary NUMBER 1110 1000011/10110 to decimal number (Show the steps in paper scan and…

A: So we will convert the binary number to decimal number.

Q: Write down the short note on Inter symbol interference.

A: In the telecommunication , Inter symbol interference is a methodology of distrotion,  in which a…

Q: Suppose you have measured a time delay of 70 microseconds between the two cursors below. The signals…

A: In this question We need to determine the angle between both signals in degree.  We know Frequency…

Q: The following ASCII code 0000110 represents

A:

Q: DRL means Logic.

A: DRL stands for

Q: . register or registers can be used for input and output purpose O DX O BX O cx O no one AX

A: AX comes under the category of the primary accumulator. It is used as the Input/output register it…

Q: To activate the ROM CS, the LS138 input must bes 001 011 100 110 111

A: The explanation is as follows.

Q: 9. For the SR Latch discussed in the lecture slides, output Q is only observed at select times…

A: Given that for SR latch is,                                            the sequence of Q for SR flip…

Q: The main difference between a register and a counter is

A: ans:(d) register has no specific sequence of states

Q: If the four output lines of a demultiplexer are YO, Y1, Y2 and Y3, and the two select lines are…

A: In this question , we will write output selected  for select lines 1 1...

Q: Question 13 A binary code to represent the decimal digits [0-9], must contain at least four bits…

A: We need to tell about decimal number which is represented by 3bits .

Q: If A = 1001 1001 0000 0010, show the result of the arithmetic shift right operation in hex

A: Given, binary number is A = 1001 1001 0000 0010, The arithmetic shift right operation in hex= ?

Q: How MLX90614 sensor will work to measure temperature based of infrared

A: MLX90614 sensor - The MLX90614 is an infrared (IR)-based non - contact temperature sensor that can…

Q: One latch can store bits of data. O a. one O b. infinite O c. many O d. two

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: DETERMINE THE BIT RATE IF A SYMBOL IS REPRESENTED BY 8 BI TS AND THE BAND IS 5000 SYMO6OL/S

A: Data can be transferred serially or parallelly. In serial data one only 1 bit transferred at a time.…

Q: Show all the base-10 digits 0-9 on a 7 segment display.

A: The solid state optic PN junction diode known as an LED, or light-emitting diode, produces light…

Q: Q2. a. Write the equivalent ASCII code of the following characters (include the space): @2 5Ba#/?8 7…

A: ASCII code- American Standard Code for Information Interchange is a form of character code in binary…

Q: If the four output lines of a demultiplexer ar YO, Y1, Y2 and Y3, and the two select lines a given…

A:

Q: A sensor is a device that converts any physical quantity into energy. O light solar mechanical…

A: A sensor is a device that measures physical input from its environment and converts it into a signal…

Q: What does the following circuit output? 1 0 1 i2 i1 i0 e |01234567 1 yo y1 y2 3x8 Decoder y4 y3 y5…

A: In this question We need to choose the correct option What is output voltage of the given circuit.…

Q: draw truth table and waveform, make sure its correct please

A: The state table can be analysed by verifying state of each flipflop after each clock.

Q: Q what is clocking block and intial block

A: Final block is executed after $finish. Final block doesn't have delay statement.Module is a block a…

Q: Question 1: Hj w) + SH(w) For the system given above determine the output, vt) when input is given…

A: Due to guidelines we can solve only first question.

Q: You have used DEBUG to unassemble the following instructions. -U 0100 0108 1369:0100 B84365 MOV AX,…

A: The instruction DEC BX has the address 1369:0106, the given address consists of segment address and…

Q: 4 to 1 What is the value of J in SoP format? MUX C' 1 Flip-Flop А В Q 2 to 4 Dec AH O A'BC + AB +…

A:

Q: art 4. Two Bit Wide 4 x 1 Multiplexer sing process INPUT_A INPUT_B OUTPUT_Y INPUT_C INPUT_D…

A:

Q: 7400 TTL series IC's can operate over a temperature range of 0 to 70°C. Select one: O True O False

A: We need to tell about the given statement is true or false.

Q: Flash type ADC is used in most of the applications . Select one: True False

A: Flash analog to digital converter: It is also known as a parallel analog to digital converter. It is…

Q: How many bits are needed to count up to a maximum of 63?

A: The given number is 63

Q: i cant really read the hand written

A: The current through a resistor is⇒I=5 mA.The colour markings for a resistor are brown, black, red…

Q: Each symbol in 8-PSK consists bits. (write the number)

A: Each symbol in 8-psk consists of _____ bits

Q: draw time diagram for write cycle and specify the content of IO/M, S1,SO at time * t1, t2, t3, t4

A:

Q: How many quantization levels are required to transfer 8-byte information

A: quantization levels are required to transfer 8-byte information

Q: It's hard to read, I need a clearly handwrite version

A:

Q: Choose the correct instruction that will send data to an I/O device. IN AL, 60 IN 60, AL OUT 60, AL…

A: Format of Instruction: Opcode Operand1, Operand2. Opcode tells about the what kind of task is to be…

Q: The regiater length is 4 bits and initially it contains 1001. Shift the register to the right six…

A:

Q: 4. Wiite a Boolean expreision for the folewag stalement Fisa if A, B&C are all I or if only twe of…

A: The solution can be achieved as follows.

Q: Drawing logical circuit shapes in digital electronics

A:

Q: Alphabetic, numeric, and special characters that can be printed on paper or displayed on a screen.…

A: Option:4 Human readable

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.