Let the dam material have specific gravity SG. The width of the dam is (b). Assume no seepage of water under the dam. Find an analytic relation between SG and the critical angle (B) for which the dam will just tip over to the right. Use your relation to compute for the special case SG =2.4 for concrete).(Ans. Cos²ß = B=64.50) 3+SG

Let the dam material have specific gravity SG. The width of the dam is (b). Assume no seepage of water under the dam. Find an analytic relation between SG and the critical angle (B) for which the dam will just tip over to the right. Use your relation to compute for the special case SG =2.4 for concrete).(Ans. Cos²ß = B=64.50) 3+SG

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1 1. What is the philosophy of the Go and No-Go gauging? Explain in some details (need schematics) 2. Complete any missing information on part 1&2 and in feature control 1 &2 (assume any tolerance). Explain your analysis ..not just numbers. 3. Add all information needed for Gage 1 & 2 used to inspect Part 1&2 (show your calculations) Part 1 Part 2 Ø1.000+.000 -.005 Ø1.005+.005 -.000 Ø.500+.000 -.005 +.005 Ø.505000 OØ. Ø. Gage 1 Gage 2 7.
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
The process defined by the figure is characterized by: O Machining tolerance class up to IT8 O Greater material removal O Excellent surface finish
Please give me answer in half hour otherwise I wil report
Solve it quickly please now
do e) f) g) with clear formatting
Please help answer all parts, thanks
Hello sir, I want to solve in a clear beautiful font that will be a manual line with a pen I know a strange request and don't forget my name and thank you sir, God bless you
|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…
I need urgent solution for this question,and dont copy paste ASAP