Mechanical Engineering Question

Q: Q5: At the instant shown in figure (5) 04 = 6 rad/s, pulley A is given an angular acceleration a =…

A: Given data: The radius of the pulley A is rA=60 mm=0.06 m The initial angular velocity of the pulley…

Q: When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

A: You have asked, When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

Q: Q1: Explain the electronic distribution of germanium, iron and magnesium if you know that their…

A: Solution to question (1) as per our Company policy:

Q: What happens to an object's motion when the forces are balanced? Group of answer choices The object…

A: Balanced forces do not change the motion of an object. The motion of an object will not change…

Q: Why does metal feel colder than wood, if they are both at the same temperature? O Metal is a…

A:

Q: A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center.  1- Two…

A:

Q: Procedure: 1. Look up the materials that make up a smartphone. Take notes in a table like the one…

A: Minerals are the substance found in the earth's crust useful to mankind. Smartphone is a Pinnacle of…

Q: Which of the following is an example of thermal technology? An engine Cell phones The furnace in…

A: Thermal technology is used for controlling, producing, transmitting work along with storing work.

Q: Duralumin alloy is Aluminum-conner allov

A: 1.a) aluminum - copper alloy 2.a) Austenitic stainless stell

Q: What is the temperature of an object where it is half as hot as 80 degrees Fahrenheit?

A: The temperature is 80°F The temperature of an object is half of the given temperature.

Q: where is the T-S diagram

A: Rankine Cycle is a ideal cycle for producing net work output in thermal power plant where water is a…

Q: Quastions about renewable

A: There are important factors are to be considered during selecting a site with good wind conditions.…

Q: The projection below is the projection of two figures, what are ?they

A: There are two figures possible as shown below

Q: The Natrium technology is one of the fastest and lowest-cost paths to provide world-changing,…

A: It is asked to mark the condenser, intermediate pressure turbines, feedwater heater, boiler…

Q: Given the views below, sketch its isometric figure.

A:

Q: How would density be used to determine the concentration of antifreeze in the cooling system of an…

A: The density of antifreeze in the cooling system of automobiles is used to determine the…

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: show the angle of declination by drawing the figure and write the important results by making the…

A: (a) Defiition: Angle of declination: It is defined as the angle between magnetic axis and…

Q: Figure Q4 shows the values of the normal and shear stresses acting on a certain stress element which…

A: Given: Normal Stress in x direction→σx=-1.5 MPa Normal Stress in y direction→σy=1 MPa Shear stress…

Q: Q.1 Who is credited with the invention of the internal combustion engine? Q.2 What common raw…

A: Internal combustion engine To find:- 1) Inventor of IC engine 2) Aluminium made from 3) Why engine…

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: What is rectification

A: Rectification is the conversion of alternating current to direct current. Rectification is performed…

Q: * 14. An entomologist observes a 1-mm-long bug with a lens of focal length 5 cm. a) The bug is…

A: GivenSize of object=1mmFocal lengthf=5cm

Q: Figure 1 of 1 8 ft 6 ft 6 ft

A:

Q: find the Ualume of 8ig below? s:de veio التل من ان ل لرمی -R

A:

Q: 500N 100N 300mm 800 N 900 N 28°

A:

Q: 5) If the lamp used is a LED lamp with an efficacy of 80 Lumen/Watt, what will be the power of the…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: The diameter of a cast iron manhole cover at 23°C is 500 mm. To what temperature should the cover be…

A: Given: d=500 mmT1=23°C∆d=1 mmα=13×106°C

Q: Is this for number 1 only?

A:

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: Round off the following number to three significant figures:2553N

A: SIgnificant digits show the value of a number in limited digits. Significants digits are very…

Q: The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank…

A: According to the problem, the water is siphoned out of the tank so the pressure at the end where the…

Q: How did you get the values for Sc=Sb and Sa=Sd

A: To get the values of enthalpy and entropy at various points we have to consider the properties table…

Q: Can You please check number 01? it is not 84.56 can you redo number 1?? v2??

A:

Q: 20 cm 30 cm

A: This is the case of the forced vortex motion. here radius = 0.3 m distance between the two limb del…

Q: A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will…

A: Given data, Gas pressure, P = 360 MPa Maximum permissible force, F = 9.50 MN = 9.50 x106 N To…

Q: Which choices are correct explanations about the scanning electron microscope (SEM)? (Select all…

A: Given Scientific electron microscope To find Suitable statement A scientific electron microscope is…

Q: Determine the x, y, z components of reaction at the journal bearing C if 0 = 0°.

A:

Q: It a lever has a mechanical advantage of 3, what does that mean? A- The work that the lever does is…

A: Mechanical advantage:  Mechanical advantage is the ratio of the output force produced by a lever to…

Q: i cant see the full workings out even on a pc, please present again so that i can see the whole…

A:

Q: 1. Compute for the force in each member of the truss in figure 1.

A:

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.