layer 28. In a doubly reinforced section, the required compressive reinforcement is provided for the: A) bending moment in excess of M lim of singly reinforced section B) bending moment equal to M lim of singly reinforced section C) shear force of the beam section D) shear force in excess of the V lim of single reinforced section

layer 28. In a doubly reinforced section, the required compressive reinforcement is provided for the: A) bending moment in excess of M lim of singly reinforced section B) bending moment equal to M lim of singly reinforced section C) shear force of the beam section D) shear force in excess of the V lim of single reinforced section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question: Civil engineering
A prestressed hollow box cross section is shown in the figure. The area of prestressed reinforcement in the tension zone is 1148 mm2. Use grade 270 for seven wire-strand tendons. fpy = specified yield strength of tendons fpu = specified tensile strength o pre stressing tendons fse = effective prestress after losses fse = 1022 MPa Aps = 1148 mm2 fpy = 0.95fpu fc' = 34.5 MPa fpu = 1860 MPa 600 mm 125 mm 350 mm 125 mm 125 mm 700 mm 500 mm 125 mm 50 mm a. Compute the Yp factor. b. Compute the stress in prestressed reinforcement at nominal strength. c. Compute for the design moment capacity. d. Compute the effective pre stressing force after losses of stress e. Compute the depth of the compression block. f. Compute the pre stressing steel ratio.
Stress and strain analysis
Design the slab reinforcement if the maximum positive moment is Mup= wul2/11 and the maximum negative moment is Mun= wul2/10. Given: Superimposed dead load = 4.76 kPa Live Load = 1.9 kPa Weight of slab = 3.45 kPa Thickness = 150 mm Length = 23.8 m Span = 3m
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
S Maximum strain in extreme fibre of concrete and in tension steel of Fe 415 grade (E = 2 x 105 N/mm²) in a balance section in limit state of flexure are respectively (a) 0.0035 and 0.0031 (b) 0.0035 and 0.0038 (c) 0.002 and 0.0042 (d) 0.002 and 0.0038
A prestressed beam has a width of 300 mm and depth of 600 mm. It is subjected to a bonded prestress tendon having an area of 590 mm2 acting at a distance 550 mm from the compression, face of the member. fc' = 34.6 MPa, fpu = 1860 MPa, fpy = 0.85fpu (stress-relived strands).COMPUTE THE STRESS IN THE PRESTRESS REINFORCEMENT AT NOMINAL STRENGTH (MPa)
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f'c = 21 MPa and steel yield strength fy = 420 MPa a.) if the tensile strain is es = fy/Es upon crushing of concrete at a strain of 0.003 b.) if the tensioe strain is set as 0.009 upon crushing of concrete at strain of 0.003 c.) minimum as required by NSCP 2015
A concrete floor slab measuring 6 m x 3 m is simply supported on one side brick load bearing walls along the 6 m sides. The concrete slab is 200 mm thick and reinforced at the bottom as follows.1. Main reinforcement (short span i.e the bars are parallel to the short span), Y 12, shape code 34 @ 125 mm centre to centre,2. Distribution reinforcement (long span i.e the bars are parallel to the long span), Y 10, shape code 20 @ 300 mm centre to centre,3. Concrete cover, 30mm,4. Concrete strength, 40MPa.Draw the reinforcement layout for this slab, in plan and section, indicating all the reinforcement and necessary information required by the contractor. You must calculate and indicate the number of bars required on your drawing. You do not need to calculate the bar lengths and the curtailment. Your drawing must be neat.
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.