Latches and Flip-Flops 363 16 Analyze the latch circuit shown. (a) Derive the next-state equation for this circuit using Q as the state variable and P as an output. (b) Construct the state table and output table for the circuit. Circle the stable states of the circuit.

Latches and Flip-Flops 363 16 Analyze the latch circuit shown. (a) Derive the next-state equation for this circuit using Q as the state variable and P as an output. (b) Construct the state table and output table for the circuit. Circle the stable states of the circuit.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Write the next-state equations for the flip-flops and the output equation. (b) Construct the transition and output tables. (c) Construct the transition graph. (d) Give a one-sentence description of when the circuit produces an output of 1. Q2 D2 Q1 T1 CLK Figure 4
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0 and will not count the last digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last digit student num:4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 0 to 9 and will not count the last two digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last two digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Q4. Analyze the following clocked synchronous sequential circuit by performing the following steps: (a) Write the equations for the flip-flop inputs and the output equation. (b) Construct the transition and output tables. (c) Construct the transition graph. (d) Give a one sentence description of when the circuit produces an output of 0. 0, D ak Q ak Clk
Reduce the Boolean function specified in the truth table below to its minimum SOP form using K-map, where A, B, C are the inputs while X are the outputs. Based on the reduced Boolean function, design the logic circuit using any logic gates. A 0 0 0 0 1 1 1 1 B 0 0 1 1 0 1 с 0 1 0 1 0 1 0 1 X 1 1 0 1 1 1 0 1
Figure Q2(e) shows a programmable logic array (PLA) unit with two inputs, four columns, and three outputs. Show the steps to implement a one-bit comparator using this PLA. Note that the output should have equal (EQ), less than (LT), and greater (GT) status. A, 02 Figure Q2(e)
(b) Analyse the sequential logic circuit for the D Flip-Flop shown in Figure below and answer the following sections Determine next state equations. Determine the state table for circuit in section (i). Draw the state machine diagram for D Flip-Flop of circuit in section (i). DD Figure (b)
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
You want to design a synchronous counter sequential logic circuit. Counting from 0 to 9 will perform and not count the numbers 0, 3, 5, 8. (a) List the steps you will apply in the design approach. State Diagram and Status Create the table. (b) Design the sequential circuit using Flip-Flops. Explain each step. Desired action show that it does.
Express the following scenario in terms of logic circuit and draw the circuit diagram. A locker has been rented in the bank. A locker gate can be opened by using one key (A) which is with the client and the other key which is with the bank (B). When both keys are used the locker door opens.
5) Draw the circuit diagram using diode and write the truth table of a logic gates whose output will be the logical OR operation of two inputs.
a) Design a logic circuit with three inputs A, B, C and an output that goes LOW only when A is HIGH while B and C are different. Draw and upload the circuit if you can, or at least describe it in words. b) Which logic gates produce a 1 output in the disabled state? c) Which logic gates pass the inverse of the input signal when these gates are enabled? d) What is the normal resting state of the SET’ and RESET’ inputs of a latch circuit (the prime is same as bar)? What is the active state of each input? e) What is the normal resting state of the NOR latch inputs? What is the active state?