Question 2)L shaped and circular cross-sectional rod has beenloaded as shown. If the allowable stress of the4m180 MPa and diameter of the rod ismaterials is o,D=60 mm, Calculate the value of the Paccording to:allowBa) Maximum shear stress criterion (Tresca),2mb) Maximum distortion energy criterion (Von Mises)NOTE:Consider only bending effect.D= 60 mmcross-section of the rod

Applying equilibrium conditions, we get: At the support,Fx = P, Fy = -PMx = 4P, My = -4P, Mz = -2P,…

L shaped and circular cross-sectional rod has been loaded as shown. If the allowable stress of the 4m materials is o=180 MPa and diameter of the rod is D=60 mm, Calculate the value of the Paccording to: a) Maximum shear stress criterion (Tresca), P 2m b) Maximum distortion energy criterion (Von Mises) P/C NOTE:Consider only bending effect. O 60 mm cross-section of the rod

L shaped and circular cross-sectional rod has been loaded as shown. If the allowable stress of the 4m materials is o=180 MPa and diameter of the rod is D=60 mm, Calculate the value of the Paccording to: a) Maximum shear stress criterion (Tresca), P 2m b) Maximum distortion energy criterion (Von Mises) P/C NOTE:Consider only bending effect. O 60 mm cross-section of the rod

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the state of plane stress shown, determine (a) the largest value of o, for which the maximum in-plane shear stress is equal to or less than 20 ksi. (b) the corresponding principal stresses. Assume stress magnitudes of S,- 31 ksi and Sy- 14 ksi. Answers: ksi (a) o, = ksi (b) opl = ksi
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0625-in. to new position Q' as shown in the figure. Determine the shear strain at Q'associated with the two edges (PQ and QR). Assume a = 4 in., b = 1 in., c = 2 in., and A = 0.0625 in. a R A Q' Answer:Y = i prad
A critical point in a part made of a ductile material is subject to the following state of plane stress: 15ksi, 30 ksi, 15 ksi, Ox,min = -35 ksi, Oy,min = 30 ksi, Txy,min = -15 ksi. Ох,max бу,max Тxy,max %3D There are no stress concentrations. The load line is propositional. The material has a yield strength of Sy = 130 ksi, an ultimate strength of Su = 200 ksi, and a fully corrected endurance limit of Sn : 75 ksi. Calculate the: (a) Static factor of safety using the MSSTF, (b) Static factor of safety using the DETF, (c) Fatigue factor of safety using the Soderberg criterion, (d) Fatigue factor of safety using the Goodman criterion, (e) Fatigue factor of safety using the ASME elliptic criterion.
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=34 kips is applied to the assembly at A, two loads of Q=25 kips are applied at B, and two loads of R=37 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 32 ksi. The normal stress magnitude in brass rod (3) must be limited to 24 ksi. Determine the minimum diameter (in in rounded to the nearest thousandths) required for rod 2.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P = 30 kips is applied to the assembly at A, two loads of Q = 20 kips are applied at B, and two loads of R = 35 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 15 ksi. The normal stress magnitude in steel rod (2) must be limited to 33 ksi. The normal stress magnitude in brass rod (3) must be limited to 22 ksi. Determine the minimum diameter required for each of the three rods. (1) R В D di in. d2 = i in. dz = i in.
At a point on the surface of a machine component the stresses acting on the e face of a stress element are or = 55 MPa and Txy = 30 MPa (see figure). T- 30 MPa a, = 55 MPa What is the allowable range of values for the stress oy if the maximum shear stress is limited to TO = 34 MPa? Round to one decimal place. (a) Lower limit is MPa (b) Upper limit is MPa
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
Consider the state of plane stress shown. (Hint: Consider both in-plane and out-of-plane shearing stresses.) 7 ksi Determine the maximum shearing stress when ox- 18 ksi and ay = 8 ksl. The maximum shearing stress is ksi.
A thin rectangular polymer plate PQRS of width b = 361 mmand height = 193 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 3.1 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. a Y = b S a urad