l' Q5/ A steel tape of nominal length 30m was suspended between supports to measure the length of a line. The measured length of the line on a slope of angle 7° is 29.859m. The mean temperature during the measurement was 12° C and the pull applied was 100 N! If standard P.o. length of the tape is 30.005m at 20° C. and the standard pull is 45N. calculate the corrected l horizontal length. Take weight of the tape = 0.15 N/m. its cross-sectional area 2.5 mm². 105 -5 1.15 x 104 °C and E= 2 x N/mm².

l' Q5/ A steel tape of nominal length 30m was suspended between supports to measure the length of a line. The measured length of the line on a slope of angle 7° is 29.859m. The mean temperature during the measurement was 12° C and the pull applied was 100 N! If standard P.o. length of the tape is 30.005m at 20° C. and the standard pull is 45N. calculate the corrected l horizontal length. Take weight of the tape = 0.15 N/m. its cross-sectional area 2.5 mm². 105 -5 1.15 x 104 °C and E= 2 x N/mm².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer within 15 minutes, please I will rate you.
00:44 allll PRACTICE QUESTIONS_GET 214-CLASS 1-2-3.pdf 6 A steel bar 300 mm long, 50 mm wide and 12 mm thick is subjected to an axial pull of 84 kN. Find the change in length, width, thickness and volume of the bar. Take E = 200 GN/m? and Poisson's ratio = 0.32. ôt = 0.0027 mm (decrease), ôV = 45.36 mm' (increase)] 7 A rectangular block 250 mm x 100 mm x 80 mm is subjected to axial loads as follows : 480 kN (tensile) in the direction of its length. 900 kN (tensile) on the 250 mm x 80 mm faces. 1000 kN (compressive) on the 250 mm x 100 mm faces. Taking E = 200 GN/m2 and Poisson's ratio as 0.25 find the following : (i) Change in volume of the block. (ii) Values of the modulus of rigidity and bulk modulus for material of the block. A bar of 30 mm diameter is subjected to a pull of 60 kN. The measured extension on gauge length of 200 mm is 0.09 mm and the change in diameter is 0.0039 mm. Cal- culate the Poisson's ratio and the values of the three modulii. 2 of 2
Please provide a solution. Thank you.
3. Considering the beam loaded as shown below. Assume EI - 50 000 kNm² 2m A B 25kN ↓ 1m 1m a. What is the slope and deflection at A? b. What is the slope and deflection at B? c. What is the slope and deflection at C? 2m 10kN/m 2m 15kN.m 1m 1m 2m
Adebe Acrobat Reader DC Window Help exercisechapter3.pdf x ト。 , 玩,唱 2/2 135% 3. Determine the vertical displacement of joint D. Given AE constant. 3 m C 4 m 4 m 15 kN 20 kN (Answer: Determine the vertical displacement of ioint Cof the truss Fach member
Answer it correctly (digital solution)
Answer is B. Show the solution
Complete answer
Hello Kindly solve this question for me
A 50-m steel tape weighing 0.035kg/m isconstantly supported at mid-length and its endpoints, and is used to measure a line AB with asteady pull of 6.5kg. If the measured length ofAB is 1200.00m, determine the following:a. Correction due to sag between supports andfor the whole tape lengthb. Total sag correction for the whole lengthmeasuredc. Correct length of line AB
Using conjugate beam method, solve the problem below
Only Handwriting Solutions need ok