l-Beam with the given measurments as follows  Flange width of 6 Inches  Height of 8 inches  Web Thickness of 2 inches  flange thickness of 1.5 Inches  Total length of beam is 24 inches (We will be using regular common steel) I need to find the shear stress, and bemding moment (assume support reactions as needed) and identify the maximum bending moment and shear stress you may modify or add measurments as needed I am trying to learn how to manually calulate. please clearly indicate so I may understand

Q: c) Discuss the following in the design of structural steel i) Bars and rods ii) Plates and flat bars

A: (i) Bars and rods A bar is a long piece having rectangular or square cross section. A rod is long…

Q: With the dimensions already given, determine the allowable value of the tensile load P, considering…

A:

Q: What will be the block shear strength of a tension member as shown in figure below? The steel is of…

A:

Q: It is a system that is composed of combination of interconnected structural elements and is used to…

A: It will be structural system and is indeterminate  Option (a) is correct option

Q: 1. Define unsymmetrical bending as it occurs in structural steel members. Illustrate two examples at…

A: Unsymmetrical Bending:- In the structural steel members, when then the plane of the bending that…

Q: The splicec connected 248 MPa сес CO

A:

Q: 143. Which of the following is not a built-up shape? Double angles c. Plate girders d. Unequal leg…

A: 143. Built-up section are the sections made by joining two or more hot rolled sections. Double…

Q: For axially loaded steel column, how could you determine that your section is safe? In case of…

A: In order to determine the safety of the steel column section. The stress available in the section is…

Q: An eyebolt is to be made out of steel having an ultimate tensile strength of 500 N/mm². If the load…

A: An eyebolt to be made out of steel- Ultimate tensile strength- σu=500 N/mm2 Factor of safety n=2,…

Q: in steel, explain effective length factors

A: Effective length factors (K-factor) are used in the analysis and design of steel structures to…

Q: 6.8 Problem: A bracket shown in figure 6.8 carries an eccentric load of 80 kN at an eccentricity o…

A:

Q: COMPUTE THE TENSILE FORCE IN CORDS A, B, C, D.

A:

Q: 7 7a 7b 7c Alaterally supported beam was designed for flexure. The beam is safe for shear &…

A: Sx of 8"x8"x7.94mm is 371.99x103 mm3

Q: Thursday Nov.24, 2020 Compute the design strength in tension, Pn, of an ASTM F1554 Gr. 36 % in…

A: Compute the design strength in tension Pn, of an ASTM F1554 Gr. 36% in diameter THREADED rod.Your…

Q: afe strength of a 5/16 in. fillet weld if it's actual length is 3 1/2 in. and the allowable unit…

A:

Q: Situation 12. With reference to the NSCP 2015, choose the correct statement: 37. For design of…

A: Tension controlled section are the RCC members which provide resistance due to primary tension…

Q: An I-section with two cover plates is used as tension member and is subjected to a load of 120 t…

A:

Q: Consider the truss shown. Determine the force acting on member CF, EF, and FG. B A D 3 m E 4 m 45 kN…

A:

Q: A steel 4340, with tensile strength of 550 Mpa and Compressive -550 Mpa with length of 3.5 mm find…

A: Permissible maximum stress to a structural member is generally subjected, that is large enough to…

Q: steel section. Check web yielding and web crippling if the steel used is ASTM A992, grade 50.

A: Solution: For W18×50, we obtain the following properties from ASTM, Below are the structural steel…

Q: Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. USE…

A:

Q: determine: (a) the elastic section modulus and the yield moment. (b) the plastic section modulus…

A: fy = 345 MPaDeterminea. Elastic modulus of section and yield moment. b. Plastic modulus of section…

Q: ction is welded to a noc owing figure shows. De equired thickness, roun

A:

Q: A 150 mm x 90 mm x 12 mm angular section is welded to a gusset plate as shown. Area of the angle is…

A: Area of the angle = 2736 sq.mmallowable shear= 150 MPaFt= 0.6FyFy= 250 MPa

Q: The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

A:

Q: 6. The round bar shown has steel, brass, and aluminum sections. Axial loads are applied at cross…

A:

Q: m alone)? (Assume bending arour

A:

Q: A steel rod of 30 mm diameter is used as a tie member in roof truss. It may be subjected to reversal…

A: Given-

Q: With the dimensions already given, determine the allowable value of the tensile load P, considering…

A: Answer  (1) Allowable normal stress at the two vertical bolts (1) and 92) is 160 Mpa Allowable…

Q: A plate is fastened to a fixed member by four 16mm rivets arranged as shown. Compute the maximum…

A: To determine the shear stress in the rivets.   Given, Diameter of the rivets (d) = 16 mm From the…

Q: Compute the deformation and member force of the truss member shown in Figure 1 under the given…

A:

Q: Define and discuss the two methods used in the design of steel members. What are the advantages and…

A: To answer No. 1

Q: Which of the following best describes a plastic hinge? Section where extreme fibers have yielded O…

A: Answer- MY < M > MP Explanation - Plastic hinge can be defined as yielded zone due to flexure…

Q: 40 mm 200 mm 40 mm

A:

Q: 5. In some cases of repairs of girders damaged by collision, the damage is severe what is used?

A: To find: What is used when repair of griders damaged by collision.

Q: A steel connecting rod with length of 6 meters and is to be subjected to a tensile load of 70 KN.…

A: ΔL = 4 mm = 0.004 m F = 70 kN = 70,000 N L = 6 m E = 200 GPa = 200,000 MPa = 200,000,000 N/m2To…

Q: 50mm 50mm 50mm P

A: Tension of plates = 75 MPaeffective hole diameter = 23 mm the joint efficiency = 80%

Q: Situation: From the given truss, determine the force in the following members: PLEASE DO NOT FORGET…

A:

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.