L-20 inches d-0.75 inch a-0.1875 inch Ea-10,000 ki Eb-17,000 ki Pa-Pb What is the thickness b? Answer in inches rounded-off to 2 decimal places Alumi (1) عالمال

Q: The pressure is the highest pressure possible in the flow, if elevation changes are neglected.…

A: The stagnation or total pressure is the pressure measured at the point where the liquid comes to…

Q: A 10 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.1 kN and a…

A:

Q: Determine the bending moment M in the beam at the point located L=4.75 m to the left of point C. The…

A:

Q: PROBLEM 5: The water in a tank is pressurized by air, and the pressure is measured by a multifluid…

A:

Q: Mechanisms 1-51. A mechanism to spray water onto vehicles at an automated car wash is shown in…

A: Given that ,  a=12 in b=1.5 in  c=14 in  d= 4 in

Q: Determine the y-coordinate of the centroid. 30 mm C -80 mm 30 mm x' a

A:

Q: Show your steps and label units on all answers. 1.) Determine the Forces in all the members, and the…

A:

Q: kindly solve the Ixx and lyy. Enclose and summarize final answers. 100 mm D 50 mm 50 mm 100 mm 60 mm…

A:

Q: 99. A gas flows through a one-inlet, one-exit control volume operating at steady state. The heat…

A:

Q: For the connection shown, the bolt diameter is d = 20 mm. The average shear stress in the bolts must…

A:

Q: 3. The shaft AB is made from L2 tool steel (shear modulus 75 GPa), has al diameter of 40 mm, and is…

A: Given data  Shear modulus= 75 GPa  Diameter= 40mm Find the maximum shear stress in AB and BC

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: 200 mm В

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: G R.75 00.63 THRU 01.123 F0.250 1.00 chamfer with distance 0.25 mm fillet with radius 0.25 mm fillet…

A: Select the correct statement about the notation circled in green and marked as letter F. Assume all…

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: The beam is made up of four boards, and is subjected to a moment of M-200 kip in, calculate the…

A:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A: P = 3.9 kNE = 210 GPa I = 5 * 106 mm4a = 1.5 mb= 1.3m

Q: 8 inch radius 8 inch circumference 8 inch all around 8 inch diameter R.70 4x 1.40 B IP 1.00 SECTION…

A: Select the correct statement about the notation circled in green and marked as letter.C. Assume all…

Q: Questions 18, 19 and 20 For the beam shown in the figure, if W is to be 500 Ib/ft and P is 2000 Ib.…

A:

Q: Q7) Choose the correct answer for the following sentences: a-45° 45' 1- The following vernier bevel…

A: Q.7 A bevel protector Is an instrument that has a graduated circular scale with one pivoted arm…

Q: Q. 2 Find the position of centroid with respect to given X and Y axis of shaded portion in the…

A:

Q: R.70 B 4x 1.40 There are 4 arched edges with radius 0.70 inches There are 4 arched edges with…

A:

Q: Find y shown in Figure below. 3 cm 0.5 cm - 0.5 cm A 1 cm B 0.5 cm D 6 cm E 0.75 cm F 0.75 cm 0.75…

A: Solution:

Q: What is the location of FR, i.e., the distance d? A M 3 m 3 m F. R B

A:

Q: PROBLEM 4: The basic barometer can be used to measure the height of a building. If the barometric…

A:

Q: Boeing 767-400ER model airplane has two engines. Each engine can have a maximum thrust (mechanical…

A:

Q: The signboard truss is designed to support a horizontal wind load of 740 lb. If the resultant of…

A:

Q: The wind chill (i.e. how cold it actually feels) is given by W(T,v) = 35.74 + 0.6215T – 35.75vº.16 +…

A: Given information: The temperature on the particular cold day (T) = 0 F The wind chill is (W) = -15

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Given:The area of struss members is the young modulus is  the load at point A is the length of AB is…

Q: Job Processing Time 1 2 3 4 5 6 7 3 9 6 5 4 5 2 Due Date 4 21 22 12 13 12 34 833 36 Processing time…

A: Given:Processing time and due date of 8 jobs are given below;

Q: Q6 Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke…

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.