Knowing that a force P of magnitude 750 N is applied to the pedal shown,determine (a) the diameter of the pin at C for which the average shearing stressin the pin is 40 MPa, (b) the corresponding bearing stress in the pedal at C, (c)the corresponding bearing stress in each support bracket at C.75 mm300 mm-mmABP125 mm5 mmCD

Answered: Image /qna-images/answer/48d03e16-74d0-4460-ad98-3887b23fe065.jpg

Answered: Knowing that a force P of magnitude 750…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Link BD consists of a single bar 30 mm wide and 12 mm thick. Knowing than each pin has a 10 mm diameter, determine the maximum value of the average normal stress in link BD if (1) 0 = 0° (2) 0= 90° 150 mm 20 kN 300 mm 30°
The rigid wrench (not the brand Rigid sold at Home Depot!) shown is used to loosen a stuck nut at the top of a 4 mm radius smooth shafted bolt that is fixed supported at the base A. Determine the largest force F that can be applied if the bolt has a maximum shear stress of for this maximum torque value. G=75 GPa 18 MPa. Also determine the distance each force will move Ans: 6.03 N F. 150 mm 150 mm 80 mm
BE CAREFUL EVERYONE HAS GOT THIS WRONG SO FAR!!!!
2. A 6 mm diameter pin is used in connection C of the pedal shown. Knowing that P = 500 N. Determine: 1. The average shear stress in the pin. 2. The average crushing effort in the pedal C. 3. The crushing stress in the supports of C. The figure is in the attached image
Problem 1 The shaft is subjected to the loading shown below. It is supported by the collar at C, which is attached to the shaft and located on the right side of the bearing at B. Determine the largest value of P for the axial forces at E and F so that the average normal stress in the shaft does not exceed an allowable tensile stress of (ot)allow = 60 MPa. A 60 mm B – 20 mm 80 mm 2P<= F C kN
Please answer d, e and f
The yoke-and-rod connection is subjected to a tensile force P. The end of the 40-mm diameter rod is embedded inside a wall at a length I of 100 mm using epoxy adhesive. If the allowable normal stress for the rods is 60 MPa, the allowable shear stress for the 25- mm diameter pin A is 50 MPa, and the allowable shear stress of the epoxy adhesive is 6 MPa, determine the largest force P that can be applied to the assembly. Note: Show your calculations for all types of stresses in detail. 40 mm 30 mm A 25 mm P.
The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is rigidly attached to the pipe, compute the length of the pipe, L, that causes the von Mises equivalent stress to be same at points H and K This IS NOT a graded assignment, it is supplementary study material.
Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section, and each of the four pins has a 16-mm diameter. Take P= 24 kN. 04 0.25 Determine the maximum value of the average normal stress in the links connecting points Cand E (Input the answer with the appropriate sign.) The maximum value of the average normal stress in the links connecting polnts Cand Eis MPa.
Link AB is to be made of a steel for which the ultimate normal stress is 450 MPa. Determine the cross-sectional area for AB for which the factor of safety will be 3.50. Assume that the link will be adequately reinforced around the pins at A and B.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 14 × 1214⁢ × 12 -in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by 3838 -in.-diameter pins, while member BCD is connected to its support at B by a 516516 -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.05 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. The largest load P that can be applied at D is lb.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS