KN/m can the cable safely Problem Number 3: Determine the maximum horizontal uniform load, w=₁ carry if the cable diameter is 105.5555 mm and has a strength of 500 MPa. What should be the estimated volume of the concrete at A (VA=_ m³)if the unit weight of concrete is Yconcrete - 23.4987 KN/m². μ = 0.3658, B= 35.8972° ✓w= ✓ TRA Details at B B 30 m 15m 20 m 120.00 m 60 m

KN/m can the cable safely Problem Number 3: Determine the maximum horizontal uniform load, w=₁ carry if the cable diameter is 105.5555 mm and has a strength of 500 MPa. What should be the estimated volume of the concrete at A (VA=_ m³)if the unit weight of concrete is Yconcrete - 23.4987 KN/m². μ = 0.3658, B= 35.8972° ✓w= ✓ TRA Details at B B 30 m 15m 20 m 120.00 m 60 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cable stretched between the fixed supports A and B is under a tension T of 3.7 kN. Express the tension as a vector using the unit vectors i and j, first, as a force TĄ acting on A and second, as a force Tg acting on B. 610 mm A y 340 mm L--- B Answers: TA = ( + 5) kN the tolerance is +/-2% Tg = ( 5) kN +
Take F = 320 N and d = 1.0 m. (Figure 1) Figure 1.5 m B C -2 m D F 1 of 1 > Part A Determine the force in cable AC needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. FAC = Submit Part B Value Request Answer Submit O ▼ Determine the force in cable AB needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. μA FAB = Value Units Request Answer wwwww Units ? ww ?
2. There are 3000 steel wire in a cable. If each wire has a dia. Of 2.257cm and design stress is 60000 N/cm2, then calculate load bearing capacity of cable.
Consider the cable shown in (Figure 1). Suppose that P-3.8 kN. P 5.8 kN Figure ya 4m +P, 6 m P (10112 -5m -2m- Determine the force P needed to hold the cable in the position shown, ie, so segment BC remains horizontal. Express your answer to three significant figures and include the appropriate units. P. Submit Request Answer Part B Value VB Compute the sag yB- Express your answer to three significant figures and include the appropriate units. Value Units Submit Request Answer OPPO ? Units
▾ Part A Determine the tension in cable AB for equilibrium. Suppose that F= 650 N. (Figure 1) Express your answer to three significant figures and include the appropriate units. HA @ DMC ? FAB= Value Units Submit Request Answer Part B Determine the tension in cable AC for equilibrium. Express your answer to three significant figures and include the appropriate units. HA 3 ➜ OWC ? FAC = Value Units Submit Request Answer Part C Determine the tension in cable AD for equilibrium. Express your answer to three significant figures and include the appropriate units. 1 ➜ DYWIC ? HA FAD = Value V Submit Request Answer 4 m 3 D -5 m Units % 5m 4 m P B C 4 m 2 m y
R-1.6 A steel plate weighing 27 kN is hoisted by a cable sling that has a clevis at each end. The pins through the cle vises are 22 mm in diameter. Each half of the cable is at an angle of 35° to the vertical. The average shear stress in ea ch pin is approximatcly: (A) 22 MPa (B) 28 MPa (C) 40 MPa (D) 48 MPa Cable sling 35 35 Clevis Steel plate
(d) A concrete beam AB of span 12 m is post-tensioned by a cable which is concentric at supports A and B and has an eccentricity of 200 mm in the mid-third span with a linear variation towards the supports. If the cable is tensioned at the jacking end A. what should be the jacking stress in the wire if the stress at B is to be 1000 N/mm²? Assume the coefficient of friction between the cable duct and concrete as 0.55 and the friction coefficient for the wave effect as 0.0015/m.
Take the allowable stress in the cable as 2000 MPa, and determine for what value of θ the cost of material used in the cable structure below will be minimum, and also determine the total volume of the material.
3. Two steel cables support a homogeneous bar AB weighing 2000 lb. The allowable stress for both steel cables is 16500 psi. Calculate the minimum area required for each cable. Answer: A = 0.06 in² 2 ft 1.5 ft 5 ft 4 B
5. Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (??) are shown in Figure 3. 6. The wood pole shown in the Figure 4 is supported by two cables of ¼ inch diameter. The turnbuckles in the cable are tightened until the stress in the cables reaches 60,000 psi. if the working compressive stress for wood is 200 psi, determine the smallest permissible diameter of the pole.
In the given flexible cable set-up carrying a uniformly distributed load spread horizontally has a magnitude of 7.5 KN/m. Fill-up the table below for the required data. Given the following = 415 MPa, f.' (concr'te) = 24 MPa, Yconcrete = 23.5 KN/m³. materials specification, fy(e (cable) Determine the Maximum Tension in The Cable = KN. - Given the capacity of the cable, determine it's diameter= For the square post at B, what will be it's theoretical dimensions, x =, What will be the total Volume of the concrete at A to serve as dead man's load = mm mm m3 10 meters 30.00 meters 20.00 meters 40.00 meter L=500 meters
The rigid beam is supported by a pin at D and cables at AE and CF. If the load P is applied at B on the beam causes the point B to be displaced 0.2 in downward, calculate the following: [ K= 18 in, a= 30 in] The normal strain in cable AE is? The normal strain in cable CF is?