kN"c" m"b" kNCK"c" m"b" kNB"C" m4 m5mA = 40 x 10° mm²A = 60 x 10° mm²A = 40 x 10° mm?Complete Solution. Thank you! 'll rate asap.Given: a = 23.5 kN, b = 22.5 kN, c = 4.5 mInstructions: 3 Decimal Places%3D%3D%3DQuestions:a. Using Cantilever method, calculate for the force in kN atmember DC.b. Using cantilever method, calmember CB.late for the axial force in kN atc. Using cantilever method, calculate for the axial force in kN atmember FE.d. Using cantilever method, calculate for the axial force in kN atmember CG.e. Using cantilever method, calculate for the axial force in kN atmember GK.

Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

KN "b" kN "b" kN B H 4m 5m A 40 x 10 mm² A = 60 x 105 mm² K A=40 x 105 mm² Complete Solution. Thank you! I'll rate asap. Given: a = 23.5 kN, b = 22.5 kN, c = 4.5 m Instructions: 3 Decimal Places Questions: a. Using Cantilever method, calculate for the force in kN at member DC. "c" m "c" m "c" m b. Using cantilever method, calculate for the axial force in kN at member CB. c. Using cantilever method, calculate for the axial force in kN at member FE.

KN "b" kN "b" kN B H 4m 5m A 40 x 10 mm² A = 60 x 105 mm² K A=40 x 105 mm² Complete Solution. Thank you! I'll rate asap. Given: a = 23.5 kN, b = 22.5 kN, c = 4.5 m Instructions: 3 Decimal Places Questions: a. Using Cantilever method, calculate for the force in kN at member DC. "c" m "c" m "c" m b. Using cantilever method, calculate for the axial force in kN at member CB. c. Using cantilever method, calculate for the axial force in kN at member FE.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

www. Wi A helical spring is fabricated by wrapping wire 3/4 in. in diameter around a forming cylinder 8 in. in diameter. Compute the number of turns required to permit an elongation of 4 in. without exceeding a shearing stress of 31 ksi. Use G = 12 x 10° psi. Use the formula: Tmaz = and d= 16PR πε3 64PR³n Gd4 + d 4R
Problem 2: Find the force in bar DB. (AE = constant.) %3! 30k D A B 12' 12' 24'
#1 will upvote anyone who will answers correctly. Thanks
(+) The hollow shaft used in the system has the following conditions: В E Outer Ø: 110 mm Ø Allowable Shearing Stress: 85 MPa 18 KN•M Determine the thickness (mm) of the shaft. Round to the F 35 kN-m nearest whole number for the thickness and use 2 decimal places for other solved values. Provide 88 kN m a torque diagram, strictly follow instructed sign convention, and start from left to right. 35 kN-m
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1179.9 Nm, U = 4330 Nm, x = 3.03 m, y = 2.25 m, z = 1.34 m, d = 94 mm, and e = 76 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places.
Engineering Mechanics. Please help to solve the problem below. Will upvote for the answer.
Assume that P = 13 kips and L = 5 ft. Determine the reaction force at C. Assume that El is constant for the beam. (Reminder: The roller symbol implies that both upward and downward displacement is restrained.) A B D L L O 11.38 kips (up) O 7.01 kips (up) O 10.44 kips (up) O 13.18 kips (up) O 14.29 kips (up)
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring at point D.
Please help me, the previous answer is wrong. ASAP. Thank you, I will like your answer if it is correct.
Note:hand written solution should be avoided.
Two blocks are supported by a pulley along an incline as shown. The lower block B has a weight of 37 lbs and the higher block A has a weight of 22 lbs. Assume that there is friction between the blocks with fls = 0.14 and assume friction between block B and the incline is also s 0.14. Determine the angle z for which motion is impending. - 27lb I Tension in block A as a function of a can be written as TA Tension in block B as a function of a can be written as TB Thus, impending motion is at = 3716 AB degrees.
#6 will upvote anyone who will answer correctly. Correct decimal places please. Thanks